Yamaha XV19CTMX(C) Скачать руководство пользователя страница 140

Страница: 140 / 494

CHASSIS

3-27

NOTE:

Using the alignment marks on each side of the
swingarm, make sure that both belt pullers are in
the same position for proper wheel alignment.

d. Tighten the locknuts to specification.

e. Tighten the rear wheel axle nut to specifica-

tion.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

5. Install:

• Muffler

Refer to “ENGINE REMOVAL” on page 5-1.

WARNING

EWA12800

Always use a new gasket.

EAS21510

CHECKING AND ADJUSTING THE
STEERING HEAD

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that the
front wheel is elevated.

2. Check:

• Steering head

Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding/looseness

→

Adjust the steering

head.

3. Remove:

• Upper bracket

Refer to “FRONT FORK” on page 4-66.

4. Adjust:

• Steering head

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the lock washer “1”, the upper ring

nut “2”, and the rubber washer “3”.

b. Loosen the lower ring nut “4”, and then tight-

en it to the specified torque with a steering nut
wrench “5”.

NOTE:

Set a torque wrench at a right angle to the steer-
ing nut wrench.

Locknut (drive belt adjusting
bolt)

16 Nm (1.6 m·kg, 11 ft·lb)

Rear wheel axle nut

150 Nm (15.0 m·kg, 110 ft·lb)

Steering nut wrench

90890-01403

Spanner wrench

YU-33975

Lower ring nut (initial tightening
torque)

52 Nm (5.2 m·kg, 37 ft·lb)

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды

Yamaha XV19CTMX(C), Руководство по обслуживанию

Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды