Yamaha XV19CTMX(C) Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 494

background image

FRONT WHEEL

4-25

2. Check:

• Front brake discs

Refer to “CHECKING THE FRONT BRAKE
DISCS” on page 4-40.

3. Lubricate:

• Oil seal lips

4. Install:

• Front wheel axle

NOTE:

Install the tire and wheel with the mark “1” point-
ing in the direction of wheel rotation.

5. Tighten:

• Front wheel axle
• Front wheel axle pinch bolt

CAUTION:

EC1D71004

Before tightening the wheel axle, push down
hard on the handlebar several times and
check if the front fork rebounds smoothly.

6. Install:

• Front brake calipers

WARNING

EWA13500

Make sure the brake hose is routed properly.

7. Install:

• Front fender
• Left front brake hose guide bracket
• Right front brake hose guide bracket

NOTE:

• Temporarily tighten the front fender bolts.
• Apply locking agent (LOCTITE®) to the

threads of the front fender bolts.

8. Install: (for XV19S(C)/ XV19M(C)/

XV19CTS(C)/ XV19CTM(C))

• Front fender stay rod “1”
• Left front fender stay “2”
• Right front fender stay “3”

NOTE:

• Insert the rod into the front wheel axle from the

right side of the vehicle.

• Tighten the left front fender stay bolt (front

side) “4” to specification while holding the rod
with a wrench “5”, and then tighten the left front
fender stay bolt (rear side) and right front fend-
er stay bolts to specification.

9. Tighten:

• Front fender bolts

Recommended lubricant

Lithium-soap-based grease

T

R

.

.

Front wheel axle

72 Nm (7.2 m·kg, 52 ft·lb)

Front wheel axle pinch bolt

23 Nm (2.3 m·kg, 17 ft·lb)

T

R

.

.

Front brake caliper bolt

40 Nm (4.0 m·kg, 29 ft·lb)

T

R

.

.

Front fender bolt

16 Nm (1.6 m·kg, 11 ft·lb)
LOCTITE®

3

2

1

4

5

«
...
176
177
178
179
180
...
»

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

Бренд: Kabuto Страницы: 25

Indian eFTR Mini 2021

Бренд: Razor Страницы: 20

990 Adventure Baja

Бренд: KTM Страницы: 227

Бренд: Graphite Страницы: 44

Бренд: Ducati Страницы: 128

Бренд: kellermann Страницы: 2

Бренд: BMW Motorrad Страницы: 146

Bonneville T100

Бренд: Triumph Страницы: 198

Freeride 350 2013

Бренд: KTM Страницы: 113

V125 Special 2018

Бренд: Lambretta Страницы: 53

Бренд: Yamaha Страницы: 98

Star XVS13CB(C)

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 145

ROADLINER XV19SW

Бренд: Yamaha Страницы: 444

Бренд: Yamaha Страницы: 494

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды