Yamaha XV19CTMX(C) Скачать руководство пользователя страница 465 | Manualshive

Страница: 465 / 494

background image

ELECTRICAL COMPONENTS

7-74

EAS27990

CHECKING THE BULBS AND BULB
SOCKETS

NOTE:

Do not check any of the lights that use LEDs.

Check each bulb and bulb socket for damage or
wear, proper connections, and also for continuity
between the terminals.
Damage/wear

→

Repair or replace the bulb,

bulb socket or both.
Improperly connected

→

Properly connect.

No continuity

→

Repair or replace the bulb, bulb

socket or both.

Types of bulbs

The bulbs used on this vehicle are shown in the
illustration.
• Bulbs “a” and “b” are used for the headlights

and usually use a bulb holder that must be de-
tached before removing the bulb. The majority
of these types of bulbs can be removed from
their respective socket by turning them coun-
terclockwise.

• Bulbs “c” are used for turn signal and tail/brake

lights and can be removed from the socket by
pushing and turning the bulb counterclockwise.

• Bulbs “d” and “e” are used for meter and indi-

cator lights and can be removed from their re-
spective socket by carefully pulling them out.

Checking the condition of the bulbs

The following procedure applies to all of the
bulbs.

1. Remove:

• Bulb

WARNING

EW1D71009

Since headlight bulbs get extremely hot,
keep flammable products and your hands
away from them until they have cooled
down.

CAUTION:

EC1D71006

• Be sure to hold the socket firmly when re-

moving the bulb. Never pull the lead, other-
wise it may be pulled out of the terminal in
the coupler.

• Avoid touching the glass part of a headlight

bulb to keep it free from oil, otherwise the
transparency of the glass, the life of the
bulb, and the luminous flux will be adverse-
ly affected. If the headlight bulb gets soiled,
thoroughly clean it with a cloth moistened
with alcohol or lacquer thinner.

2. Check:

• Bulb (for continuity)

(with the pocket tester)
No continuity

→

Replace.

NOTE:

Before checking for continuity, set the pocket
tester to “0” and to the “

Ω

×

1” range.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the positive tester probe to terminal

“1” and the negative tester probe to terminal
“2”, and check the continuity.

b. Connect the positive tester probe to terminal

“1” and the negative tester probe to terminal
“3”, and check the continuity.

c. If either of the readings indicate no continuity,

replace the bulb.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

«
...
463
464
465
466
467
...
»

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

Бренд: Yamaha Страницы: 572

Бренд: Yamaha Страницы: 584

Бренд: Yamaha Страницы: 410

Бренд: Yamaha Страницы: 576

Бренд: Yamaha Страницы: 668

Бренд: Yamaha Страницы: 596

Бренд: Yamaha Страницы: 656

Бренд: Yamaha Страницы: 378

HUSABERG MX 2000

Бренд: Ohlins Страницы: 16

Бренд: Parweld Страницы: 37

Бренд: Honda Страницы: 60

Бренд: Isotta Страницы: 2

RACE 11621C0520

Бренд: Yoshimura Страницы: 7

Бренд: MOTO GUZZI Страницы: 134

Бренд: Takegawa Страницы: 2

Бренд: Shark Страницы: 80

Бренд: VESPA Страницы: 80

Бренд: Wunderkind Custom Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды