Yamaha XV19CTMX(C) Скачать руководство пользователя страница 186

Страница: 186 / 494

REAR WHEEL

4-33

EAS22110

CHECKING THE REAR WHEEL DRIVE HUB

1. Check:

• Rear wheel drive hub

Cracks/damage

→

Replace.

• Rear wheel drive hub dampers

Damage/wear

→

Replace.

EAS22130

CHECKING AND REPLACING THE REAR
WHEEL PULLEY

1. Check:

• Rear wheel pulley

Surface plating has come off

→

Replace the

rear wheel pulley.
Bent teeth

→

Replace the rear wheel pulley.

2. Replace:

• Rear wheel pulley

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the self-locking nuts and the rear

wheel pulley.

b. Clean the rear wheel drive hub with a clean

cloth, especially the surfaces that contact the
pulley.

c. Install the new rear wheel pulley.

NOTE:

Tighten the self-locking nuts in stages and in a
crisscross pattern.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS22140

ASSEMBLING THE REAR WHEEL

1. Install:

• Wheel bearings

• Oil seals

Refer to “ASSEMBLING THE FRONT
WHEEL” on page 4-23.

EAS22150

ADJUSTING THE REAR WHEEL STATIC
BALANCE

NOTE:

• After replacing the tire, wheel or both, the rear

wheel static balance should be adjusted.

• Adjust the rear wheel static balance with the

brake disc and rear wheel drive hub installed.

1. Adjust:

• Rear wheel static balance

Refer to “ADJUSTING THE FRONT WHEEL
STATIC BALANCE” on page 4-23.

EAS28770

INSTALLING THE REAR WHEEL (DISC)

1. Lubricate:

• Rear wheel axle
• Oil seal lips

2. Install:

• Rear brake disc
• Rear brake disc cover

NOTE:

• Apply locking agent (LOCTITE®) to the

threads of the brake disc bolts.

• Tighten the brake disc bolts in stages and in a

crisscross pattern.

3. Check:

• Rear brake disc

Refer to “CHECKING THE REAR BRAKE
DISC” on page 4-53.

4. Install:

• Rear wheel axle
• Washer
• Rear wheel axle nut

Rear wheel pulley self-locking
nut

95 Nm (9.5 m·kg, 68 ft·lb)

New

Recommended lubricant

Lithium-soap-based grease

Rear brake disc bolt

18 Nm (1.8 m·kg, 13 ft·lb)
LOCTITE®

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды

Yamaha XV19CTMX(C), Руководство по обслуживанию

Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды