manualshive.com logo in svg

Yamaha XV19CTMX(C), Руководство по обслуживанию

Yamaha XV19CTMX(C) - это мощный мотоцикл, который требует правильного обслуживания. Получите бесплатный сервисный мануал для этой модели, чтобы узнать, как правильно заботиться о ней. Скачайте его с manualshive.com и следуйте инструкциям для долгой и безопасной езды.

Поделиться
Скачать
background image

REAR SHOCK ABSORBER ASSEMBLY AND SWINGARM

4-86

EAS23180

HANDLING THE REAR SHOCK ABSORBER

WARNING

EWA13740

This rear shock absorber contains highly 
compressed nitrogen gas. Before handling 
the rear shock absorber, read and make sure 
you understand the following information. 
The manufacturer cannot be held responsi-
ble for property damage or personal injury 
that may result from improper handling of 
the rear shock absorber.
• Do not tamper or attempt to open the rear 

shock absorber.

• Do not subject the rear shock absorber to 

an open flame or any other source of high 
heat. High heat can cause an explosion due 
to excessive gas pressure.

• Do not deform or damage the rear shock 

absorber in any way. Rear shock absorber 
damage will result in poor damping perfor-
mance.

EAS23190

DISPOSING OF A REAR SHOCK ABSORBER

1. Gas pressure must be released before dis-

posing of a rear shock absorber. To release 
the gas pressure, drill a 2–3 mm (0.08–0.12 
in) hole through the rear shock absorber at a 
point 15–20 mm (0.59–0.79 in) from its end 
as shown.

WARNING

EWA13760

Wear eye protection to prevent eye damage 
from released gas or metal chips.

ET1D71002

REMOVING THE REAR SHOCK ABSORBER 
ASSEMBLY AND SWINGARM

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is 
no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that the 
rear wheel is elevated.

2. Loosen:

• Engine mounting nut (rear lower side)

Refer to “ENGINE REMOVAL” on page 5-1.

NOTE:

Because there is force being exerted on the en-
gine mounting bracket (left and right rear lower 
sides), it is necessary to loosen the engine 
mounting nut (rear lower side) in order to create 
some space between the connecting arms and 
engine bracket before removing the rear shock 
absorber and swingarm.

3. Remove:

• Connecting arm bolt (frame side)

NOTE:

When removing the connecting arm bolt (frame 
side), hold the swingarm so that it does not drop 
down.

4. Measure:

• Swingarm side play
• Swingarm vertical movement

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Measure the tightening torque of the pivot 

shaft nut.

b. Measure the swingarm side play “A” by mov-

ing the swingarm from side to side.

c. If the swingarm side play is out of specifica-

tion, check the spacers, bearings, washers, 
and oil seals.

d. Check the swingarm vertical movement “B” 

by moving the swingarm up and down.
If swingarm vertical movement is not smooth 
or if there is binding, check the spacers, bear-
ings, washers, and oil seals.

T

 

R

.

.

 

Pivot shaft nut

125 Nm (12.5 m·kg, 90 ft·lb)

 

Swingarm side play (at the end of 
the swingarm)

1.0 mm (0.04 in)

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

Yamaha XVS650A Owner'S Manual preview
XVS650A
Бренд: Yamaha Страницы: 86
Yamaha TW125 Parts Catalog preview
TW125
Бренд: Yamaha Страницы: 57
Yamaha TT-R90(R) Owner'S Service Manual preview
TT-R90(R)
Бренд: Yamaha Страницы: 288
Yamaha TRACER 700 2020 Owner'S Manual preview
TRACER 700 2020
Бренд: Yamaha Страницы: 98
Yamaha QT50 Service Manual preview
QT50
Бренд: Yamaha Страницы: 118
Yamaha XV1700PCR Road Star Warrior Owner'S Manual preview
XV1700PCR Road Star Warrior
Бренд: Yamaha Страницы: 122
Yamaha YZFR1W 2007 Service Manual preview
YZFR1W 2007
Бренд: Yamaha Страницы: 429
Yamaha XT225C Service Manual preview
XT225C
Бренд: Yamaha Страницы: 427
Yamaha Moto matrix YZF-R6S Supplementary Service Manual preview
Moto matrix YZF-R6S
Бренд: Yamaha Страницы: 41
hepco & becker Minirack 6602533 01 01 Manual preview
Minirack 6602533 01 01
Бренд: hepco & becker Страницы: 4
OKBABY No shock Quick Start Manual preview
No shock
Бренд: OKBABY Страницы: 35
Dakota Digital MLX-3000 Manual preview
MLX-3000
Бренд: Dakota Digital Страницы: 11
Kabuto LEFF Instruction Manual preview
LEFF
Бренд: Kabuto Страницы: 20
Suzuki GSX-R600 Manual preview
GSX-R600
Бренд: Suzuki Страницы: 165
Zero SR/S Service Manual preview
SR/S
Бренд: Zero Страницы: 290
Pro Moto Billet Fastway PMB-01-5203 Quick Manual preview
Fastway PMB-01-5203
Бренд: Pro Moto Billet Страницы: 2
Yamaha PW50 2020 Owner'S Manual preview
PW50 2020
Бренд: Yamaha Страницы: 74
Yamaha PW50 2013 Owner'S Manual preview
PW50 2013
Бренд: Yamaha Страницы: 76

Бренды по названию

Популярные бренды

Загрузить еще бренды