Yamaha XV19CTMX(C) Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 494

background image

CHASSIS

3-26

EAS21430

ADJUSTING THE DRIVE BELT SLACK

NOTE:

The drive belt slack must be checked at the tight-
est point on the belt.

CAUTION:

ECA14950

A drive belt that is too tight will overload the
engine and other vital parts, and one that is
too loose can skip and damage the swing-
arm or cause an accident. Therefore, keep
the drive belt slack within the specified lim-
its.

NOTE:

Measure the drive belt slack when the engine is
cold, and when the drive belt is dry.

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

NOTE:

Place the vehicle on the sidestand and or on a
suitable stand so that the rear wheel is elevated.

2. Check:

• Drive belt slack “a”

Out of specification

→

Adjust.

NOTE:

• The level marks of the level window on the low-

er drive belt cover are in units of 5 mm (0.20 in).
Use them as a standard for measuring the
drive belt slack.

• Measure the drive belt slack when the drive

belt has been pushed with 4.5 kg (10 lbs) of
pressure using a belt tension gauge “1”.

3. Remove:

• Muffler

Refer to “ENGINE REMOVAL” on page 5-1.

4. Adjust:

• Drive belt slack

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

NOTE:

Place the vehicle on a suitable stand so that the
rear wheel is elevated.

a. Loosen the wheel axle nut “1”.

b. Loosen both locknuts “2”.
c. Turn both adjusting bolts “3” in direction “a” or

“b” until the specified drive belt slack is ob-
tained.

Drive belt slack (on the side-
stand)

7.5–13 mm (0.30–0.51 in)

Drive belt slack (on a suitable
stand)

14–21 mm (0.55–0.83 in)

Belt tension gauge

90890-03170

Rear drive belt tension gauge

YM-03170

a

Direction “a”

Drive belt is tightened.

Direction “b”

Drive belt is loosened.

1

1

«
...
137
138
139
140
141
...
»

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

Бренд: HYOSUNG Страницы: 199

Бренд: R&G Страницы: 6

Бренд: TB Страницы: 8

Бренд: Nolan Страницы: 80

Бренд: Wolfman Страницы: 3

Бренд: SCHUBERTH Страницы: 43

Бренд: Twiins Страницы: 40

Бренд: Tipperary Страницы: 2

RR 125 2T MY 2018

Бренд: Beta Motorcycles Страницы: 138

Бренд: Beta Страницы: 74

TERMOSCUD-R204X

Бренд: tucanourbano Страницы: 2

TERMOSCUD R200X

Бренд: tucanourbano Страницы: 4

TERMOSCUD R192X

Бренд: tucanourbano Страницы: 4

Бренд: Sealey Страницы: 2

Бренд: Beta Страницы: 196

Бренд: Beta Страницы: 360

Бренд: hepco & becker Страницы: 2

250 EXC-F AUS 2012

Бренд: KTM Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды