Yamaha XV19CTMX(C) Скачать руководство пользователя страница 410 | Manualshive

Страница: 410 / 494

background image

LIGHTING SYSTEM

7-19

EAS27260

TROUBLESHOOTING

Any of the following fail to light: headlight (high beam), headlight (low beam), high beam indicator light,
taillight, license light, position light, meter light or accessory light (OPTION).

NOTE:

• Before troubleshooting, remove the following part(s):
1. Rider seat
2. Tool kit tray
3. Headlight assembly

NG

→

OK

↓

NG

→

OK

↓

NG

→

OK

↓

NG

→

OK

↓

NG

→

OK

↓

NG

→

OK

↓

NG

→

OK

↓

1. Check the condition of each bulb

and bulb socket.
Refer to “CHECKING THE BULBS
AND BULB SOCKETS” on page
7-74.

Replace the bulb(s) and bulb socket(s).

2. Check the fuses.

(Main, headlight, signaling system,
taillight and ECU (for XV19S(C)/
XV19M(C)/ XV19CTS(C)/
XV19CTM(C)))
Refer to “CHECKING THE FUS-
ES” on page 7-75.

Replace the fuse(s).

3. Check the battery.

Refer to “CHECKING AND
CHARGING THE BATTERY” on
page 7-76.

• Clean the battery terminals.
• Recharge or replace the battery.

4. Check the main switch.

Refer to “CHECKING THE
SWITCHES” on page 7-71.

Replace the main switch.

5. Check the dimmer switch.

Refer to “CHECKING THE
SWITCHES” on page 7-71.

The dimmer switch is faulty. Replace the
left handlebar switch.

6. Check the accessory light switch.

Refer to “CHECKING THE
SWITCHES” on page 7-71.

The accessory light switch is faulty. Re-
place the right handlebar switch.

7. Check the headlight relay.

Refer to “CHECKING THE RE-
LAYS” on page 7-79.

Replace the headlight relay.

«
...
408
409
410
411
412
...
»

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

B-TRK502-02-01-SL

Бренд: SRC Страницы: 4

STEADYSTAND Cross Basic

Бренд: ACEBIKES Страницы: 6

Super Adventure 2016

Бренд: KTM Страницы: 25

Бренд: Caberg Страницы: 16

Бренд: R&G Страницы: 4

Бренд: N-Com Страницы: 32

Бренд: Artotic Страницы: 9

Бренд: Suzuki Страницы: 165

Multistrada 620

Бренд: Ducati Страницы: 382

Бренд: Memphis Shades Страницы: 2

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

EMPORIO ARMANI 946 2015

Бренд: VESPA Страницы: 416

Бренд: Baotian Страницы: 30

Бренд: Benelli Страницы: 454

DUCATI IGCS0703

Бренд: Peg-Perego Страницы: 24

Бренд: Malaguti Страницы: 242

Бренд: Gazzini Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды