Yamaha XV19CTMX(C) Скачать руководство пользователя страница 276

Страница: 276 / 494

CAMSHAFTS

5-27

5. Measure:

• Crankcase hole inside diameter “a”

Out of specification

→

Replace the crank-

case.

6. Measure:

• Camshaft cover hole inside diameter “a”

Out of specification

→

Replace the camshaft

cover.

7. Calculate:

• Camshaft-to-crankcase clearance

Out of specification

→

Replace the defective

part(s).

NOTE:

Calculate the clearance by subtracting the cam-
shaft journal diameter (crankcase side) from the
crankcase hole inside diameter.

8. Calculate:

• Camshaft to camshaft cover clearance

Out of specification

→

Replace the defective

part(s).

NOTE:

Calculate the clearance by subtracting the cam-
shaft journal diameter (camshaft cover side)
from the camshaft cover hole inside diameter.

9. Check:

• Camshaft drive gears
• Camshaft driven gears
• Front cylinder camshaft gears
• Rear cylinder camshaft gears

Chips/pitting/roughness/wear

→

Replace the

defective part(s).

EAS23890

CHECKING THE ROCKER ARMS AND
ROCKER ARM SHAFTS

The following procedure applies to all of the
rocker arms and rocker arm shafts.
1. Check:

• Rocker arm

Damage/wear

→

Replace.

2. Check:

• Rocker arm shaft

Blue discoloration/excessive wear/pitting/
scratches

→

Replace or check the lubrication

system.

3. Measure:

• Rocker arm inside diameter “a”

Out of specification

→

Replace.

Crankcase hole inside diameter

25.000–25.021 mm (0.9843–
0.9851 in)

Camshaft cover hole inside diam-
eter

28.000–28.021 mm (1.1024–
1.1032 in)

Camshaft to crankcase clearance

0.020–0.064 mm (0.0008–0.0025
in)

Camshaft to camshaft cover
clearance

0.020–0.064 mm (0.0008–0.0025
in)

Rocker arm inside diameter

18.000–18.018 mm (0.7087–
0.7094 in)

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды

Yamaha XV19CTMX(C), Руководство по обслуживанию

Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды