manualshive.com logo in svg

Yamaha XV19CTMX(C), Руководство по обслуживанию

Yamaha XV19CTMX(C) - это мощный мотоцикл, который требует правильного обслуживания. Получите бесплатный сервисный мануал для этой модели, чтобы узнать, как правильно заботиться о ней. Скачайте его с manualshive.com и следуйте инструкциям для долгой и безопасной езды.

Поделиться
Скачать
background image

ENGINE

3-16

4. Remove:

• Air filter element “1”

5. Check:

• Air filter element

Damage 

→

 Replace.

NOTE:

The air filter needs more frequent service if you 
are riding in unusually wet or dusty areas.

6. Install:

• Air filter case cover

CAUTION:

EC1D71002

Never operate the engine without the air filter 
element installed. Unfiltered air will cause 
rapid wear of engine parts and may damage 
the engine. Operating the engine without the 
air filter element will also affect the throttle 
body synchronization, leading to poor en-
gine performance and possible overheating.

NOTE:

When installing the air filter element into the air 
filter case, make sure that the sealing surfaces 
are aligned to prevent any air leaks.

7. Install:

• Fuel tank

Refer to “FUEL TANK” on page 6-1.

• Rider seat

Refer to “GENERAL CHASSIS” on page 4-1.

EAS21010

CHECKING THE THROTTLE BODY JOINTS

The following procedure applies to all of the 
throttle body joints and intake manifolds.
1. Remove:

• Rider seat
• Rider seat bracket assembly

Refer to “GENERAL CHASSIS” on page 4-1.

• Fuel tank

Refer to “FUEL TANK” on page 6-1.

• Air filter case

Refer to “GENERAL CHASSIS” on page 4-1.

2. Check:

• Throttle body joints “1”

Cracks/damage 

→

 Replace.

3. Install:

• Air filter case

Refer to “GENERAL CHASSIS” on page 4-1.

• Fuel tank

Refer to “FUEL TANK” on page 6-1.

• Rider seat bracket assembly
• Rider seat

Refer to “GENERAL CHASSIS” on page 4-1.

EAS21030

CHECKING THE FUEL LINE

The following procedure applies to all of the fuel, 
air vent and breather hoses.
1. Remove:

• Rider seat
• Rider seat bracket assembly

Refer to “GENERAL CHASSIS” on page 4-1.

• Fuel tank

Refer to “FUEL TANK” on page 6-1.

2. Check:

• Fuel hoses “1”
• Air vent hose “2”
• Breather hose “3”

Cracks/damage 

→

 Replace.

Loose connection 

→

 Connect properly.

CAUTION:

ECA14940

Make sure the fuel tank breather hose is rout-
ed correctly.

1

1

1

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

Öhlins SD 047 Mounting Instruction preview
SD 047
Бренд: Öhlins Страницы: 8
Öhlins prodrive SUR 3A00 Mounting Instructions preview
prodrive SUR 3A00
Бренд: Öhlins Страницы: 4
Öhlins HO 404 Mounting Instructions preview
HO 404
Бренд: Öhlins Страницы: 2
Öhlins HO 201 Owner'S Manual preview
HO 201
Бренд: Öhlins Страницы: 2
Öhlins FCX 0302 Mounting Instructions preview
FCX 0302
Бренд: Öhlins Страницы: 8
Öhlins DU 907 Mounting Instructions preview
DU 907
Бренд: Öhlins Страницы: 4
R&G ECC0364R Fitting Instructions Manual preview
ECC0364R
Бренд: R&G Страницы: 6
MRA 4025066171910 Mounting Instructions preview
4025066171910
Бренд: MRA Страницы: 9
GAS GAS EC-SIX DAYS - PART LIST 2011 Parts List preview
EC-SIX DAYS - PART LIST 2011
Бренд: GAS GAS Страницы: 6
Pandora Smart Moto Manual preview
Smart Moto
Бренд: Pandora Страницы: 56
Miller AirArmor User Manual preview
AirArmor
Бренд: Miller Страницы: 22
hepco & becker 506998 00 01 Quick Start Manual preview
506998 00 01
Бренд: hepco & becker Страницы: 2
hepco & becker 610060 00 01 Manual preview
610060 00 01
Бренд: hepco & becker Страницы: 3
Hama 00201973 Operating Instructions Manual preview
00201973
Бренд: Hama Страницы: 22
Derbi SENDA R/SM 125 4T Baja Manual preview
SENDA R/SM 125 4T Baja
Бренд: Derbi Страницы: 124
Scott Safety FH4 Operating And Maintenance Instructions Manual preview
FH4
Бренд: Scott Safety Страницы: 67
R&G PKS0119 Fitting Instructions Manual preview
PKS0119
Бренд: R&G Страницы: 6
R&G RAD0253 Series Fitting Instructions Manual preview
RAD0253 Series
Бренд: R&G Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды