Yamaha XV19CTMX(C) Скачать руководство пользователя страница 175

Страница: 175 / 494

FRONT WHEEL

4-22

EAS21900

REMOVING THE FRONT WHEEL

1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

2. Remove: (for XV19S(C)/ XV19M(C)/

XV19CTS(C)/ XV19CTM(C))

• Right front fender stay “1”
• Left front fender stay “2”
• Front fender stay rod “3”

NOTE:

• Remove the right front fender stay bolts and

left front fender stay bolt (rear side), then hold
the rod with a wrench “4” and remove the left
front fender stay bolt (front side) “5”.

• Remove the rod from the right side of the vehi-

cle.

3. Loosen:

• Front wheel axle pinch bolt “1”

4. Remove:

• Front brake calipers

NOTE:

Do not apply the brake lever when removing the
brake calipers.

5. Elevate:

• Front wheel

NOTE:

Place the vehicle on a suitable stand so that the
front wheel is elevated.

EAS21910

DISASSEMBLING THE FRONT WHEEL

1. Remove:

• Oil seals
• Wheel bearings

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Clean the outside of the front wheel hub.
b. Remove the oil seals “1” with a flathead

screwdriver.

NOTE:

To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel surface.

c. Remove the wheel bearings “3” with a gener-

al bearing puller.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS21920

CHECKING THE FRONT WHEEL

1. Check:

• Front wheel axle

Roll the wheel axle on a flat surface.
Bends

→

Replace.

WARNING

EWA13460

Do not attempt to straighten a bent wheel ax-
le.

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды

Yamaha XV19CTMX(C), Руководство по обслуживанию

Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды