Yamaha XV19CTMX(C) Скачать руководство пользователя страница 416

Страница: 416 / 494

SIGNALING SYSTEM

7-25

→

↓

The neutral indicator light fails to come on.

→

↓

→

↓

→

↓

The fuel level gauge fails to operate.

→

↓

→

↓

The fuel level warning light fails to come on.

→

↓

4. Check the entire signaling system

wiring.
Refer to “CIRCUIT DIAGRAM” on
page 7-21.

Properly connect or repair the signaling
system wiring.

This circuit is OK.

1. Check the neutral switch.

Refer to “CHECKING THE
SWITCHES” on page 7-71.

Replace the neutral switch.

2. Check the relay unit (diode).

Refer to “CHECKING THE DI-
ODES” on page 7-81.

Replace the relay unit.

3. Check the entire signaling system

wiring.
Refer to “CIRCUIT DIAGRAM” on
page 7-21.

Properly connect or repair the signaling
system wiring.

This circuit is OK.

1. Check the fuel sender (fuel tank).

Refer to “CHECKING THE FUEL
SENDER (FUEL TANK)” on page
7-88.

Replace the fuel sender.

2. Check the entire signaling system

wiring.
Refer to “CIRCUIT DIAGRAM” on
page 7-21.

Properly connect or repair the signaling
system wiring.

Replace the meter assembly.

1. Check the fuel level warning light.

Refer to “CHECKING THE FUEL
LEVEL WARNING LIGHT” on page
7-89.

Replace the meter assembly or fuel pump
assembly.

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды

Yamaha XV19CTMX(C), Руководство по обслуживанию

Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды