Yamaha XV19CTMX(C) Скачать руководство пользователя страница 224

Страница: 224 / 494

FRONT FORK

4-71

EAS22960

REMOVING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Stand the vehicle on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is
no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that the
front wheel is elevated.

2. Loosen:

• Lower bracket pinch bolts

WARNING

EW1D71007

Before loosening the lower bracket pinch
bolts, support the front fork leg.

EAS22980

DISASSEMBLING THE FRONT FORK LEGS

The following procedure applies to both of the
front fork legs.
1. Drain:

• Fork oil

NOTE:

Stroke the outer tube several times while drain-
ing the fork oil.

2. Remove:

• Dust seal “1”
• Oil seal clip “2”

(with a flathead screwdriver)

CAUTION:

ECA14180

Do not scratch the inner tube.

3. Remove:

• Damper rod bolt “1”
• Copper washer

NOTE:

While holding the damper rod with the damper
rod holder “2” and T-handle “3”, loosen the
damper rod bolt.

4. Remove:

• Inner tube

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Hold the front fork leg horizontally.
b. Securely clamp the brake caliper bracket in a

vise with soft jaws.

c. Separate the inner tube from the outer tube

by pulling the inner tube forcefully but careful-
ly.

CAUTION:

ECA14190

• Excessive force will damage the oil seal

and bushing. A damaged oil seal or bush-
ing must be replaced.

• Avoid bottoming the inner tube into the out-

er tube during the above procedure, as the
oil flow stopper will be damaged.

Damper rod holder

90890-01460

T-handle

90890-01326

T-handle 3/8" drive 60 cm long

YM-01326

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды

Yamaha XV19CTMX(C), Руководство по обслуживанию

Результаты поиска

Содержание XV19CTMX(C)

Отзывы:

Похожие инструкции для XV19CTMX(C)

Бренды по названию

Популярные бренды