Yamaha XV19CTMX(C) Скачать руководство пользователя страница 384 | Manualshive

Страница: 384 / 494

background image

THROTTLE BODIES

6-15

ET1D71026

REMOVING THE FUEL HOSE

1. Disconnect:

• Fuel hose (intake manifold assembly to pres-

sure regulator)

CAUTION:

EC1D71014

Although the fuel has been removed from
the fuel tank be careful when removing the
fuel hose, since there may be fuel remaining
in it.

NOTE:

• To remove the fuel hose from the fuel pipe or

pressure regulator, slide the fuel hose connec-
tor cover “1” on the end of the hose in the direc-
tion of the arrow shown, press the two buttons
“2” on the sides of the connector, and then re-
move the hose.

• Remove the fuel hose manually without using

any tools.

• Before removing the hoses, place a few rags in

the area under where they will be removed.

EAS26980

CHECKING THE INJECTORS

1. Check:

• Injectors

Damage

→

Replace.

EAS26990

CHECKING THE THROTTLE BODIES

1. Check:

• Throttle bodies

Cracks/damage

→

Replace the throttle bod-

ies as a set.

2. Check:

• Fuel passages

Obstructions

→

Clean.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Wash the throttle bodies in a petroleum-

based solvent.
Do not use any caustic carburetor cleaning
solution.

b. Blow out all of the passages with compressed

air.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

ET1D71007

CHECKING THE ROLLOVER VALVES

1. Check:

• Rollover valve 1 “1”
• Rollover valve 2 “2”

Damage/faulty

→

Replace.

NOTE:

• Check that air flows smoothly only in the direc-

tion of the arrow shown in the illustration.

• The rollover valves must be in an upright posi-

tion when checking the airflow.

EAS27000

CHECKING THE PRESSURE REGULATOR

1. Check:

• Pressure regulator

Damage

→

Replace.

EAS27010

CHECKING THE PRESSURE REGULATOR
OPERATION

1. Check:

• Pressure regulator operation

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the pressure regulator cover.

Refer to “THROTTLE BODIES” on page 6-7.

b. Disconnect the fuel hose “1” from the pres-

sure regulator “2”.

c. Connect the fuel pressure adapter “3” be-

tween the fuel hose “1” and pressure regula-
tor “2”.

d. Connect the pressure gauge “4” to the fuel

pressure adapter “3”.

e. Connect the vacuum/pressure pump gauge

set “5” to the pressure regulator.

1

2

1

2

«
...
382
383
384
385
386
...
»

Содержание XV19CTMX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19CTMX(C)

Бренд: Can-Am Страницы: 16

Бренд: Can-Am Страницы: 254

Бренд: KTM Страницы: 29

Lock-it TANKRING 506003

Бренд: hepco & becker Страницы: 2

Бренд: PEUGEOT Страницы: 12

Splendor Pro CLASSIC

Бренд: HERO Страницы: 56

Бренд: hepco & becker Страницы: 5

GRIZZLY 90 2020

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 132

Бренд: Yamaha Страницы: 166

Бренд: Yamaha Страницы: 452

Бренд: Yamaha Страницы: 132

Бренд: kellermann Страницы: 5

Бренд: DYNATEK Страницы: 8

Бренд: Palm Страницы: 14

Бренд: Shad Страницы: 2

KIT TOPMASTER S0BN11ST

Бренд: Shad Страницы: 2

KIT TOPMASTER S0SV69ST

Бренд: Shad Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды