Yamaha MBK MW125 2014 Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 380

background image

FUEL TANK

7-2

EAS30450

REMOVING THE FUEL TANK

1. Extract the fuel in the fuel tank through the

fuel tank filler hole with a pump.

2. Disconnect:

• Fuel pump coupler “1”
• Fuel sender coupler “2”

3. Remove:

• Fuel hose connector cover “3”

4. Disconnect:

• Fuel hose “4”

WARNING

EWA18020

Cover the fuel hose connection with a cloth
when disconnecting it. Residual pressure in
the fuel lines could cause fuel to spurt out
when removing the hose.

NOTICE

ECA21750

• Be sure to disconnect the fuel hose by

hand. Do not forcefully disconnect the
hose with tools.

• Although the fuel has been removed from

the fuel tank, be careful when removing the
fuel hose, since there may be fuel remain-
ing in it.

• Do not disconnect the fuel hose from the

fuel hose connector. Disconnect the con-
nector from the fuel pump.

TIP

Before removing the hose, place a few rags in
the area under where it will be removed.

5. Remove:

• Fuel tank

EAS30451

REMOVING THE FUEL PUMP

1. Remove:

• Fuel pump

NOTICE

ECA14720

• Do not drop the fuel pump or give it a

strong shock.

• Do not touch the base section of the fuel

sender.

EAS30454

CHECKING THE FUEL PUMP BODY

1. Check:

• Fuel pump body

Obstruction

→

Clean.

Cracks/damage

→

Replace fuel pump as-

sembly.

EAS31249

CHECKING THE FUEL FILTER

1. Check:

• Fuel filter

Damage

→

Replace.

Contaminants

→

Clean with solvent.

EAS30456

INSTALLING THE FUEL PUMP

1. Install:

• Fuel pump gasket
• Fuel pump
• Fuel pump bracket

TIP

• Do not damage the installation surfaces of the

fuel tank when installing the fuel pump.

• Always use a new fuel pump gasket.
• Install the fuel pump as shown in the illustra-

tion.

• Align the punch mark “a” on the fuel tank with

the projection “b” on the fuel pump.

• Align the projection “b” on the fuel pump with

the slot in the fuel pump bracket.

• Tighten the fuel pump bolts in the proper tight-

ening sequence as shown.

EAS30457

INSTALLING THE FUEL TANK

1. Install:

• Fuel hose

1

2

3

4

T

R

.

.

Fuel pump bracket bolt

3.8 Nm (0.38 m·kgf, 2.8 ft·lbf)

New

2

4

1

3

a

b

FWD

«
...
283
284
285
286
287
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: MadStad Engineering Страницы: 2

Бренд: Parkside Страницы: 89

Бренд: Parkside Страницы: 28

Бренд: GLOBBER Страницы: 72

Бренд: R&G Страницы: 8

Mesh Helmet Cover

Бренд: Ops-Core Страницы: 2

Бренд: MV Agusta Страницы: 36

TwinSpark Super head plus R

Бренд: Takegawa Страницы: 5

Бренд: BMW Страницы: 416

Бренд: Cake Страницы: 12

Бренд: CRATONI Страницы: 61

Бренд: BMW Motorrad Страницы: 231

TorqDrive Clutch Pack

Бренд: Rekluse Страницы: 18

Бренд: Yamaha Страницы: 398

Бренд: Yamaha Страницы: 666

Бренд: Yamaha Страницы: 190

Бренд: DYNATEK Страницы: 5

Бренд: Dynafit Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды