Yamaha MBK MW125 2014 Скачать руководство пользователя страница 332 | Manualshive

Страница: 332 / 380

background image

FUEL INJECTION SYSTEM

8-35

Fault code No. 16

2

Connection of wire harness
ECU coupler.
Check the locking condition of
the coupler.
Disconnect the coupler and
check the pins (bent or broken
terminals and locking condition
of the pins).

Improperly connected

→

Con-

nect the coupler securely or re-
place the wire harness.

Turn the main switch to “ON”.
Fault code number is not dis-
played

→

Service is finished.

Fault code number is displayed

→

Go to item 3.

3

Wire harness continuity.

Open or short circuit

→

Replace

the wire harness.
Between throttle body sensor
assembly coupler and ECU
coupler.
black/blue–black/blue
yellow–yellow
blue–blue

Turn the main switch to “ON”.
Fault code number is not dis-
played

→

Service is finished.

Fault code number is displayed

→

Go to item 4.

4

Installed condition of throttle
body sensor assembly.
Check for looseness or pinch-
ing.

Improperly installed sensor

→

Reinstall sensor.

Turn the main switch to “ON”.
Fault code number is not dis-
played

→

Service is finished.

Fault code number is displayed

→

Go to item 5.

5

Defective throttle position sen-
sor.

Check throttle position sensor
signal.
Execute the diagnostic mode.
(Code No. 01)
When the throttle valve is fully
closed:
A value of 14–20 is indicated.
When throttle valve is fully
open:
A value of 97–107 is indicated.
An indicated value is out of the
specified range

→

Replace the

throttle body.

Turn the main switch to “ON”.
Fault code number is not dis-
played

→

Service is finished.

Fault code number is displayed

→

Go to item 6.

6

Malfunction in ECU.

Replace the ECU.
Refer to “REPLACING THE
ECU (engine control unit)” on
page 8-59.

Fault code No.

15

Item

Throttle position sensor: open or short circuit detected.

Fault code No.

16

Item

Throttle position sensor is stuck.

Fail-safe system

Able to start engine

Able to drive vehicle

Diagnostic code No.

01

Tool display

Throttle position sensor signal
• 14–20 (Fully closed position)
• 97–107 (Fully open position)

Procedure

• Check with throttle valve fully closed.
• Check with throttle valve fully open.

Item

Probable cause of malfunc-

tion and check

Maintenance job

Confirmation of service com-

pletion

«
...
330
331
332
333
334
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: KAYO MOTOR Страницы: 61

Бренд: probrake Страницы: 2

Бренд: Yamaha Страницы: 287

SBL.04.650.10000/B

Бренд: SW-Motech Страницы: 2

Бренд: NZI Helmets Страницы: 4

Бренд: GYS Страницы: 36

ZTechnik VStream Z2392

Бренд: National Cycle Страницы: 2

MULTISTRADA 1200S

Бренд: Ducati Страницы: 311

Бренд: Honda Страницы: 556

Бренд: Yamaha Страницы: 215

Бренд: Yamaha Страницы: 319

Бренд: Yamaha Страницы: 688

XMAX YP250R 2013

Бренд: Yamaha Страницы: 94

Бренд: ICON Vehicle Dynamics Страницы: 4

Бренд: digades Страницы: 10

Бренд: JETPRIME Страницы: 5

Бренд: Sealey Страницы: 2

Бренд: Benelli Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды