Yamaha MBK MW125 2014 Скачать руководство пользователя страница 364

Страница: 364 / 380

ELECTRICAL COMPONENTS

8-67

b. Move the fuel sender float to minimum “3”

and maximum “4” level position.

c. Measure the fuel sender resistance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS30578

CHECKING THE COOLANT TEMPERATURE
SENSOR

1. Remove:

• Thermostat assembly

Refer to “THERMOSTAT” on page 6-5.

WARNING

EWA14130

• Handle the coolant temperature sensor

with special care.

• Never subject the coolant temperature sen-

sor to strong shocks. If the coolant temper-
ature sensor is dropped, replace it.

2. Check:

• Coolant temperature sensor resistance

Out of specification

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Connect the pocket tester (

100/

1 k

) to

the coolant temperature sensor terminals as
shown.

b. Immerse the coolant temperature sensor “1”

in a container filled with coolant “2”.

TIP

Make sure that the coolant temperature sensor
terminals do not get wet.

c. Place a thermometer “3” in the coolant.

d. Heat the coolant or let it cool down to the

specified temperatures.

e. Measure the coolant temperature sensor re-

sistance.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

3. Install:

• Thermostat assembly

EAS30681

CHECKING THE FUEL INJECTORS

1. Check:

• Fuel injector resistance

Out of specification

→

Replace the fuel injec-

tor.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Disconnect the fuel injector coupler from wire

harness.

b. Connect the pocket tester (

1) to the fuel

injector terminals as shown.

Coolant temperature sensor re-
sistance

5166–6314

@0 °C (5166–6314

@32 °F)

Coolant temperature sensor re-
sistance

288-352

@80 °C (288-352

@176 °F)

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Thermostat assembly bolt

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

Resistance

12.0

Pocket tester

90890-03112

Analog pocket tester

YU-03112-C

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды