Yamaha MBK MW125 2014 Скачать руководство пользователя страница 153

Страница: 153 / 380

FRONT BRAKE

4-44

WARNING

EWA13540

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids
may result in a harmful chemical reaction,
leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake master cylinder reser-
voir. Water will significantly lower the boil-
ing point of the brake fluid and could cause
vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.

5. Bleed:

• Brake system

Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-12.

6. Check:

• Brake fluid level

Below the minimum level mark “a”

→

Add the

specified brake fluid to the proper level.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-12.

7. Check:

• Brake lever operation

Soft or spongy feeling

→

Bleed the brake sys-

tem.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-12.

EAS30179

REMOVING THE FRONT BRAKE MASTER
CYLINDER

TIP

Before removing the front brake master cylinder,
drain the brake fluid from the entire brake sys-
tem.

1. Remove:

• Brake hose union bolt “1”
• Copper washers “2”
• Front brake hose “3”

TIP

To collect any remaining brake fluid, place a
container under the master cylinder and the end
of the brake hose.

EAS30725

CHECKING THE FRONT BRAKE MASTER
CYLINDER

1. Check:

• Brake master cylinder

Damage/scratches/wear

→

Replace.

• Brake fluid delivery passages

(brake master cylinder body)
Obstruction

→

Blow out with compressed air.

2. Check:

• Brake master cylinder kit

Damage/scratches/wear

→

Replace.

3. Check:

• Brake master cylinder reservoir cap
• Brake master cylinder reservoir diaphragm

holder

• Brake master cylinder reservoir diaphragm

Damage/wear

→

Replace.

4. Check:

• Front brake hose

Cracks/damage/wear

→

Replace.

Specified brake fluid

YAMAHA GENUINE BRAKE
FLUID (DOT 4)

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды