Yamaha MBK MW125 2014 Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 380

Yamaha MBK MW125 2014 Скачать руководство пользователя страница 204

ENGINE INSPECTION

5-1

EAS20041

ENGINE INSPECTION

EAS30249

MEASURING THE COMPRESSION
PRESSURE

TIP

Insufficient compression pressure will result in a
loss of performance.

1. Remove:

• Center cover

Refer to “GENERAL CHASSIS (1)” on page
4-1.

2. Measure:

• Valve clearance

Out of specification

→

Adjust.

Refer to “ADJUSTING THE VALVE CLEAR-
ANCE” on page 3-4.

3. Start the engine, warm it up for several min-

utes, and then turn it off.

4. Disconnect:

• Spark plug cap

5. Remove:

• Spark plug

NOTICE

ECA20470

Before removing the spark plug, use com-
pressed air to blow away any dirt accumulat-
ed in the spark plug well to prevent it from
falling into the cylinder.

6. Install:

• Compression gauge “1”
• Compression gauge extensions S “2”

7. Measure:

• Compression pressure

Out of specification

→

Refer to steps (c) and

(d).

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Turn the main switch to “ON”.
b. With the throttle wide open, crank the engine

until the reading on the compression gauge
stabilizes.

WARNING

EWA12940

To prevent sparking, ground all spark plug
leads before cranking the engine.

c. If the compression pressure is above the

maximum specification, check the cylinder
head, valve surfaces and piston crown for
carbon deposits.
Carbon deposits

→

Eliminate.

d. If the compression pressure is below the min-

imum specification, pour a teaspoonful of en-
gine oil into the spark plug bore and measure
again.
Refer to the following table.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

8. Install:

• Spark plug

9. Connect:

• Spark plug cap

Compression gauge

90890-03081

Engine compression tester

YU-33223

Compression gauge extension S

90890-03195

1

2

Standard compression pressure
(at sea level)

1600 kPa/725 r/min (16.0
kgf/cm²/725 r/min, 227.6 psi/725
r/min)

Minimum–maximum

1392–1792 kPa/725 r/min (13.9–
17.9 kgf/cm²/725 r/min, 198.0–
254.9 psi/725 r/min)

Compression pressure (with oil applied into the
cylinder)

Reading

Diagnosis

Higher than without oil

Piston ring(s) wear or
damage

→

Repair.

Same as without oil

Piston, valves, cylinder
head gasket or piston
ring(s) possibly defec-
tive

→

Repair.

T

R

.

.

Spark plug

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

«
...
202
203
204
205
206
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов