Yamaha MBK MW125 2014 Скачать руководство пользователя страница 216

Страница: 216 / 380

CYLINDER HEAD

5-13

2. Check:

• Cylinder head

Damage/scratches

→

Replace.

• Cylinder head water jacket

Mineral deposits/rust

→

Eliminate.

3. Measure:

• Cylinder head warpage

Out of specification

→

Resurface the cylinder

head.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Place a straightedge “1” and a thickness

gauge “2” across the cylinder head.

b. Measure the warpage.
c. If the limit is exceeded, resurface the cylinder

head as follows.

d. Place 400–600 grit wet sandpaper on the sur-

face plate and resurface the cylinder head
using a figure-eight sanding pattern.

TIP

To ensure an even surface, rotate the cylinder
head several times.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

EAS31232

CHECKING THE CAMSHAFT SPROCKET

1. Check:

• Camshaft sprocket

More than 1/4 tooth wear “a”

→

Replace the

camshaft sprocket, timing chain and crank-
shaft as a set.

EAS30279

CHECKING THE TIMING CHAIN TENSIONER

1. Check:

• Timing chain tensioner

Cracks/damage

→

Replace.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the timing chain tensioner plug.
b. While lightly pressing the timing chain ten-

sioner rod by hand, turn the tensioner rod ful-
ly clockwise with a thin screwdriver “1”.

c. Remove the screwdriver and slowly release

the timing chain tensioner rod.

Warpage limit

0.05 mm (0.0020 in)

a. 1/4 tooth
b. Correct
1. Timing chain roller
2. Camshaft sprocket

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды