manualshive.com logo in svg

Yamaha MBK MW125 2014, Руководство по обслуживанию, Страница: 268 / 380

Поделиться
Скачать
Yamaha MBK MW125 2014 Скачать руководство пользователя страница 268

CRANKSHAFT

5-65

3. Measure:

• Crankshaft width

Out of specification 

→

 Replace the crank-

shaft assembly.

4. Check:

• Crankshaft sprocket “1”

Damage/wear 

→

 Replace the crankshaft as-

sembly.

• Bearing “2”

Cracks/damage/wear 

→

 Replace the crank-

shaft assembly.

EAS31243

CHECKING THE CRANKCASE

1. Thoroughly wash the crankcase halves in a 

mild solvent.

2. Thoroughly clean all the gasket surfaces and 

crankcase mating surfaces.

3. Check:

• Crankcase

Cracks/damage 

→

 Replace.

EAS31244

CHECKING THE BEARING

1. Check:

• Bearing

Clean and lubricate the bearings, and then 
rotate the inner race with your finger.
Rough movement 

→

 Replace.

EAS31245

CHECKING THE OIL PUMP DRIVE GEAR

1. Check:

• Oil pump drive gear

Damage/wear 

→

 Replace.

EAS30791

INSTALLING THE CRANKSHAFT

1. Install:

• Crankshaft assembly “1”

TIP

Install the crankshaft assembly with the crank-
shaft installer pot “2”, crankshaft installer bolt “3”, 
adapter “4”, and crankshaft installer spacer “5”.

NOTICE

ECA13970

To avoid scratching the crankshaft and to 
ease the installation procedure, lubricate the 
oil seal lips with lithium-soap-based grease 
and each bearing with engine oil.

 

Crank assembly width

45.45–45.50 mm (1.789–1.791 in)

1

2

 

Crankshaft installer pot

90890-01274

Installing pot

YU-90058

Crankshaft installer bolt

90890-01275

Bolt

YU-90060

Adapter (M12)

90890-01278

Adapter #3

YU-90063

Crankshaft installer spacer

90890-04156

1

5

4

3

2

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов