Yamaha MBK MW125 2014 Скачать руководство пользователя страница 100

Страница: 100 / 380

PERIODIC MAINTENANCE

3-19

TIP

• Before checking the engine oil level, wait a few

minutes until the oil has settled.

• Do not screw the dipstick in when inspecting

the oil level.

NOTICE

ECA13370

Do not allow foreign materials to enter the
crankcase.

5. Start the engine, warm it up for several min-

utes, and then turn it off.

6. Check the engine oil level again.

TIP

Before checking the engine oil level, wait a few
minutes until the oil has settled.

7. Install:

• Dipstick

EAS30657

CHANGING THE ENGINE OIL

1. Start the engine, warm it up for several min-

utes, and then turn it off.

2. Place a container under the engine oil drain

bolt.

3. Remove:

• Dipstick “1”
• Engine oil drain bolt “2”

(along with the gasket)

4. Drain:

• Engine oil

(completely from the crankcase)

5. If the oil strainer is also to be cleaned, per-

form the following procedure.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Remove the oil strainer cover “1”, spring “2”,

and oil strainer “3”.

b. Install a new O-ring “4”.

c. Install the oil strainer, spring, and oil strainer

cover.

Recommended brand

YAMALUBE

Type

SAE 10W-40, 20W-40 or 20W-50

Recommended engine oil grade

API service SG type or higher,
JASO standard MA or MB

–20 –10 0

10 20 30 40 50 ˚C

10 30 50 70 90 110

130 ˚F

SAE 20W-50

SAE 20W-40

SAE 10W-40

New

Содержание MBK MW125 2014





























































































































































































































































































































































































Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды

Yamaha MBK MW125 2014, Руководство по обслуживанию

Результаты поиска

Содержание MBK MW125 2014

Отзывы:

Похожие инструкции для MBK MW125 2014

Бренды по названию

Популярные бренды