Yamaha MBK MW125 2014 Скачать руководство пользователя страница 326 | Manualshive

Страница: 326 / 380

background image

FUEL INJECTION SYSTEM

8-29

The engine operation is not normal, but the engine trouble warning light does not come on.

1. Check the operation of the following sensors and actuators in the diagnostic mode. Refer to “TROU-

BLESHOOTING DETAILS” on page 8-30.

If a malfunction is detected in the sensors or actuators, repair or replace all faulty parts.
If no malfunction is detected in the sensors and actuators, check and repair the inner parts of the
engine.

EAS30951

YAMAHA DIAGNOSTIC TOOL

This model uses the Yamaha diagnostic tool to identify malfunctions.
For information about using the Yamaha diagnostic tool, refer to the operation manual that is included
with the tool.

Features of the Yamaha diagnostic tool
You can use the Yamaha diagnostic tool to identify malfunctions quicker than with conventional meth-
ods.
By connecting the adapter interface, which is connected to the USB port of a computer, to a vehicle’s
ECU using the communication cable, you can display information that is necessary for identifying mal-
functions and for maintenance to display on the computer. The displayed information includes the sen-
sor output data and information recorded in the ECU.
Functions of the Yamaha diagnostic tool

However, the diagnostic tool cannot be used to freely change the basic vehicle functions, such as ad-
justing the ignition timing.
Connecting the Yamaha diagnostic tool
Disconnect the Yamaha diagnostic tool connector, and then connect the Yamaha diagnostic tool to the
connector “1”.

01: Throttle position sensor signal (throttle angle)
30: Ignition coil
36: Injector

Yamaha diagnostic tool

90890-03231

Fault diagnosis mode:

Fault codes recorded on the ECU are read, and the contents are dis-
played.

Function diagnostic mode:

Check the operation of the output value of each sensor and actuator.

Inspection mode:

Determine whether each sensor or actuator is functioning properly.

CO adjustment mode:

Adjust the concentration of CO admissions during idling.

Monitoring mode:

Displays a graph of sensor output values for actual operating condi-
tions.

Logging mode:

Records and saves the sensor output value in actual driving conditions.

View log:

Displays the logging data.

ECU rewrite:

If necessary, the ECU is rewritten using ECU rewrite data provided by
Yamaha.
Ignition timing adjustment, etc. cannot be changed from the vehicle’s
original state.

«
...
324
325
326
327
328
...
»

Содержание MBK MW125 2014





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MBK MW125 2014

Бренд: Kappa Страницы: 4

Бренд: KAYO MOTOR Страницы: 61

Бренд: BV Powersports Страницы: 40

Бренд: NewMar Страницы: 116

Бренд: R&G Страницы: 10

Бренд: SCHUBERTH Страницы: 41

Бренд: Lakeland Страницы: 16

Бренд: B&G electronics Страницы: 5

Бренд: hepco & becker Страницы: 4

TorqDrive Clutch Pack

Бренд: Rekluse Страницы: 18

Бренд: DYNATEK Страницы: 12

gtrack 7855 MyBASIC

Бренд: Gemini Страницы: 20

Бренд: Enerwatt Страницы: 26

Бренд: Baotian Страницы: 26

Бренд: MZ Страницы: 204

Бренд: Beta Страницы: 93

2009 Evo 2T 125

Бренд: Beta Страницы: 192

Бренд: hepco & becker Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды