manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 98

Trouble Recovery

92

 

 

EMU32131

Power tilt will not operate

If the engine cannot be tilted up or down with
the power tilt because of a discharged bat-
tery or a failure with the power tilt unit, the en-
gine can be tilted manually.
1. Loosen the manual valve screw by turn-

ing it counterclockwise until it stops.

2. Put the engine in the desired position,

then tighten the manual valve screw by
turning it clockwise.

EMU29534

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

EWM01023

Use this procedure only in an emergen-
cy to return to the nearest port for re-
pairs.

When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not oper-
ate. Make sure the remote control lever
is in neutral. Otherwise the boat could
unexpectedly start to move, which
could result in an accident.

Attach the engine shut-off cord to a se-
cure place on your clothing, or your
arm or leg while operating the boat.

Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.

Avoid accidentally pulling the cord dur-

1. Fuse puller
2. Cap
3. Fuse (20 A)
4. Spare fuse (20 A)

1. Fuse puller

ZMU05565

1

2

3

4

1

ZMU04337

1. Manual valve screw

6AG-9-3D-1E0.book  92 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды