manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 58

Operation

52

or leg. Then install the clip on the other
end of the cord into the engine shut-off
switch.

3. Place the throttle grip in the “

”

(start) position. After the engine starts,
return the throttle to the fully closed po-
sition.

4. Push the starter button to start the en-

gine.

5. Immediately after the engine starts, re-

lease the starter button and allow it to re-

turn to its original position. 

NOTICE:

Never push the starter button while
the engine is running. Do not keep
the starter motor turning for more
than 5 seconds. If the starter motor is
turned continuously for more than 5
seconds, the battery will be quickly
discharged, thus making it impossi-
ble to start the engine. The starter can
also be damaged. If the engine will
not start after 5 seconds of cranking,
release the starter button, wait 10
seconds, then crank the engine
again.

 [ECM00162]

TIP:

When the engine is cold, it needs to be
warmed up. For further information, see
page 54.

If the engine is warm and fails to start,
open the throttle slightly and try to start the
engine again. If the engine still fails to
start, see page 88.

6. Slowly return the throttle grip to the fully

closed position.

EMU27666

Electric start and remote control models

WARNING

EWM01842

Failure to attach the engine shut-off
cord could result in a runaway boat if
operator is ejected. Attach the engine
shut-off cord to a secure place on your
clothing, or your arm or leg while oper-
ating. Do not attach the cord to clothing
that could tear loose. Do not route the
cord where it could become entangled,
preventing it from functioning.

Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power,

ZMU02026

ZMU06522

ZMU05521

6AG-9-3D-1E0.book  52 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды