manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 48

Operation

42

dent could occur.

NOTICE

ECM00121

Do not start the engine out of water. Over-
heating and serious engine damage can
occur.

EMU36561

Fuel level

Be sure you have plenty of fuel for your trip.
A good rule is to use 1/3 of your fuel to get to
the destination, 1/3 to return, and to keep 1/3
as an emergency reserve. With the boat lev-
el on a trailer or in the water, check the fuel
level. For fuel filling instructions, see page
45.

EMU36573

Remove the top cowling

For the following checks, remove the top
cowling from the bottom cowling. To remove
the top cowling, release the cowling lock le-
ver and lift off the top cowling.

 

EMU36443

Fuel system

WARNING

EWM00061

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other sourc-
es of ignition.

WARNING

EWM00911

Leaking fuel can result in fire or explo-
sion.

Check for fuel leakage regularly.

If any fuel leakage is found, the fuel
system must be repaired by a qualified
mechanic. Improper repairs can make
the outboard unsafe to operate.

EMU36453

Check for fuel leaks

Check for fuel leaks or gasoline fumes in
the boat.

Check for fuel leakage from the fuel sys-
tem.

Check the fuel tank and fuel lines for
cracks, swellings, or other damage.

EMU37323

Checking the fuel filter

Check that the fuel filter is clean and free of
water. If any water is found in the fuel, or if a
significant amount of debris is found, the fuel
tank should be checked and cleaned by a
Yamaha dealer.

 

EMU36903

Controls

Tiller handle models:

Move the tiller handle fully to the left and
right to make sure operation is smooth.

Turn the throttle grip from the fully closed
to the fully open position. Make sure that it

ZMU06169

6AG-9-3D-1E0.book  42 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды