manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 66

Operation

60

TIP:

Depending on the type of boat, the outboard
motor trim angle may have little effect on the
trim of the boat when operating.

EMU27936

Tilting up and down

If the engine will be stopped for some time or
if the boat is moored in shallows, the out-
board motor should be tilted up to protect the
propeller and lower casing from damage by
collision with obstructions, and also to re-
duce salt corrosion.

WARNING

EWM00223

Make sure that no one is near the out-
board motor when tilting the outboard
motor up or down. Otherwise, body parts
could be crushed between the outboard
motor and the clamp bracket.

WARNING

EWM00251

Leaking fuel is a fire hazard. If there is a
fuel joint on the outboard motor, discon-
nect the fuel line or close the fuel cock if
the engine will be tilted for more than a
few minutes. Otherwise fuel may leak.

NOTICE

ECM00242

Before tilting the outboard motor, stop
the engine by following the procedure

on page 56. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this
could break the handle.

EMU43222

Procedure for tilting up (manual tilt 
models)

1. Place the remote control lever / gear

shift lever in neutral.

2. Disconnect the fuel hose from the fuel

joint on the outboard motor.

N

ZMU03087

ZMU05533

N

6AG-9-3D-1E0.book  60 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды