manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 102

Trouble Recovery

96

8. Insert the knotted end of the emergency

starter rope into the notch in the flywheel
rotor and wind the rope 1 or 2 turn(s)
around the flywheel clockwise.

9. Pull the rope slowly until resistance is

felt. Give a strong pull straight out to
crank and start the engine. If the engine
does not start on the first try, repeat the
procedure.

TIP:

If the engine does not start on the first try,
repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If
the engine still fails to start, see page 49.

Slowly return the throttle grip to the fully
closed position so that the engine does not
stall.

EMU33502

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately. 

NOTICE:

 Do not attempt to run the

outboard motor until it has been com-
pletely inspected.

 [ECM00402]

ZMU05533

N

ZMU01772

ZMU02026

ON START

OFF

ZMU01906

ZMU05622

6AG-9-3D-1E0.book  96 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды