manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 51

Operation

45

EMU34783

Checking power tilt system

WARNING

EWM01971

Never get under the lower unit while it
is tilted, even when the tilt support
knob is locked. Severe injury could oc-
cur if the outboard motor accidentally
falls.

Body parts can be crushed between the
motor and the clamp bracket when the
motor is trimmed or tilted.

Be sure no one is near the outboard
motor before performing this check.

1. Check the power tilt unit for any sign of

oil leaks.

2. Operate each of the power tilt switches

to check that all switches work.

3. Tilt the outboard motor up and check

that the tilt rod is pushed out completely.

4. Check that the tilt rod is free of corrosion

or other flaws.

5. Tilt the outboard motor down. Check that

the tilt rod operates smoothly.

EMU36585

Battery

Check the battery’s charge. If your boat is
equipped with a Yamaha digital speedome-
ter, the voltmeter and low battery alert func-
tions will help you monitor the battery’s
charge. A battery in good condition will pro-
vide a minimum of 12 volts. Check that the
battery connections are clean, secure and
covered by insulating covers. The electrical
connections of the battery and cables must
be clean and properly connected or the bat-
tery will not start the engine.
If the battery needs charging, consult your
Yamaha dealer or the battery manufacturer’s
instructions.

EMU43164

Filling fuel

WARNING

EWM01831

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,
change your clothes.

Before refueling, check the following points:

Ensure the engine is stopped.

1. Tilt rod

6AG-9-3D-1E0.book  45 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды