manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 54

Operation

48

ing the air vent screw.

This product emits exhaust gases
which contain carbon monoxide, a col-
orless, odorless gas which could cause
brain damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and cab-
in areas well ventilated. Avoid blocking
exhaust outlets.

EMU43174

Sending fuel (portable tank)

1. To loosen the air vent screw, turn it

counterclockwise until it stops.

2. Check the direction of the fuel hose.

Make sure that the arrow of the primer
pump points toward the outboard motor.

3. Align the fuel joint on the fuel hose with

the fuel joint on the outboard motor and
firmly connect the fuel hose to the joint
while pinching the joint.

4. Firmly connect the other end of the fuel

hose to the joint on the fuel tank.

5. Wipe up any spilled gasoline immediate-

ly with dry rags.

TIP:

Dispose of rags properly according to local
laws or regulations.
6. Squeeze the primer pump, with the ar-

row pointing up, until you feel it become

1. Air vent screw

1. Toward the outboard motor
2. Arrow
3. Primer pump

1

ZMU07445

ZMU07452

1

4

3

2

4. Toward the fuel tank

1. Fuel joint
2. Fuel hose

1. Fuel joint
2. Fuel hose

ZMU08026

1

2

ZMU07455

2

1

6AG-9-3D-1E0.book  48 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды