Yamaha Electone F-15 Скачать руководство пользователя страница 37

Страница: 37 / 110

Components

TIP:

For instructions on using the power tilt
switch, see pages 57 and 60.

EMU31433

Steering friction adjuster

A friction device provides adjustable resis-
tance to the steering mechanism, and can be
set according to operator preference. An ad-
juster lever is located on the bottom of the til-
ler handle bracket.
To increase resistance, turn the lever to the

port side “A”.
To decrease resistance, turn the lever to the
starboard side “B”.

WARNING

EWM00041

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to steer, which could result in an
accident.

If the resistance does not increase even
when the lever is turned to the port side “A”,
make sure that the nut is tightened to the
specified torque.

TIP:



Steering movement is blocked when the
adjuster lever is set to the “A” position.

ZMU01720

ZMU05579

ZMU04899

1. Nut

Nut tightening torque:

8 Nm (0.82 kgf-m, 5.9 ft-lb)

ZMU05522

ZMU05523

6AG-9-3D-1E0.book 31 ページ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Результаты поиска

Содержание Electone F-15

Отзывы:

Бренды по названию

Популярные бренды

Yamaha Electone F-15, Руководство пользователя

Результаты поиска

Содержание Electone F-15

Отзывы:

Бренды по названию

Популярные бренды