manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 60

Operation

54

water pump is pumping water through the
cooling water passages. If the cooling water
passages are frozen, it may take a while for
water to start flowing out of the pilot hole.

NOTICE

ECM01811

If water is not flowing out of the pilot hole
at all times while the engine is running,
overheating and serious damage could
occur. Stop the engine and check wheth-
er the cooling water inlet on the lower
case or the cooling water pilot hole is
blocked. Consult your Yamaha dealer if
the problem cannot be located and cor-
rected.

 

EMU27671

Warming up engine

EMU27718

Manual start and electric start 
models

1. After starting the engine, allow it to idle

for 3 minutes to warm up. 

NOTICE:

 Fail-

ure to do so will shorten engine life.

[ECM04550]

2. Be sure the low oil pressure-alert indica-

tor goes off after starting the engine.

NOTICE:

 If the low oil pressure-alert

indicator blinks after the engine
starts, stop the engine. Otherwise,
serious engine damage could occur.

Check the oil level and add engine oil
if necessary. Consult your Yamaha
dealer if the cause for the low oil
pressure alert cannot be found.

[ECM01832]

EMU36532

Checks after engine warm up

EMU36542

Shifting

While the boat is tightly moored, and without
applying throttle, confirm that the engine
shifts smoothly into forward and reverse, and
back to neutral.

EMU36981

Stop switches

Turn the main switch to “

”, or press the

engine stop button and make sure the en-
gine stops.

Confirm that removing the clip from the en-
gine shut-off switch stops the engine.

Confirm that the engine cannot be started
with the clip removed from the engine
shut-off switch.

EMU34563

Shifting

WARNING

EWM00181

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

NOTICE

ECM01611

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting
back to neutral. If this occurs, stop the
engine, shift to neutral, then restart the
engine and allow it to warm up.

To shift out of neutral
1. Pull the neutral interlock trigger up (if

6AG-9-3D-1E0.book  54 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды