manualshive.com logo in svg

Yamaha Electone F-15, Руководство пользователя

Поделиться
Скачать
Yamaha Electone F-15 Скачать руководство пользователя страница 76

Maintenance

70

7. Fill the tank with fresh water to above the

level of the anti-cavitation plate.

NOTICE:

 If the fresh water level is be-

low the level of the anti-cavitation
plate, or if the water supply is insuffi-
cient, engine seizure may occur.

[ECM00292]

8. Cooling system flushing is essential to

prevent the cooling system from clog-
ging up with salt, sand, or dirt. In addi-
tion, fogging of the engine is mandatory
to prevent excessive engine damage
due to rust. Perform the flushing and
fogging at the same time. 

WARNING!

Do not touch or remove electrical
parts when starting or during opera-
tion. Keep hands, hair, and clothes
away from the flywheel and other ro-
tating parts while the engine is run-
ning.

 [EWM00092]

9. Run the engine at a fast idle for 10–15

minutes in neutral position.

10. Just prior to turning off the engine, quick-

ly spray “Yamaha Stor-Rite Engine
Fogging Oil” alternately into each carbu-
retor or the fogging hole of the silencer
cover, if equipped. When properly done,
the engine will smoke excessively and

almost stall.

11. Remove the outboard motor from the

test tank. For further details, see page
67.

12. Drain the cooling water completely out of

the outboard motor. Clean the body thor-
oughly.

13. Install the silencer cover/cap (if

equipped) and top cowling.

EMU41072

Lubrication

1. Change the gear oil. For instructions,

see page 84. Check the gear oil for the
presence of water that indicates a leaky
seal. Seal replacement should be per-
formed by an authorized Yamaha dealer
prior to use.

2. Lubricate all grease fittings. For further

details, see page 77.

TIP:

For long-term storage, fogging the engine
with fogging oil is recommended. Contact
your Yamaha dealer for information about
fogging oil and procedures for your outboard
motor.

EMU30268

Cleaning and anticorrosion 
measures

1. Wash down the exterior of the outboard

motor with fresh water and dry off com-
pletely. 

NOTICE:

 Do not spray water

into the air intake.

 [ECM01841]

 For further

information, see page 71.

2. Spray the outboard motor exterior with

“Yamaha Silicone Protectant”. 

NOTICE:

Do not spray when the engine is run-
ning. Also, do not spray near the si-
lencer or into the engine. Otherwise
the engine could be damaged.

 [ECM01403]

3. Wax the cowling with a non-abrasive

wax such as “Yamaha Silicone Wax”.

1. Water surface
2. Lowest water level

ZMU02051

1

2

6AG-9-3D-1E0.book  70 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Содержание Electone F-15















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды