Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 95

Страница: 95 / 145

Figure 41:

RX Serial and Parallel Clock Divider

IBUFDS_GTM

MGTREFCLKP
MGTREFCLKN

ODIV2

REFCLK_HROW_CK_SEL

REFCLK Distribution

REFCLK SEL

LCPLL

RX PROG

DIV

TXP/N

RX DATA

RX PCS

RX PMA

RX DATA to Downstream

PCS Blocks

Output Clock to BUFG_GT

Output to

GTM_DUAL

GTM_DUAL (GTM Transceiver Primitive)

Phase
Interp.

RX CLKGEN

SIPO

ADC

DSP

CDR

/16

Output to

MGTREFCLK Pad

RXRECCLK[0/1] from the other GTM RX

channel within the same GTM_DUAL

Gray

Decoder

Pre-

Coder

Polarity

Control

RXRECCLK[0/1]

RX FIFO

CH[0/1]_RXUSRCLK

CH[0/1]_RXPROGDIVCLK

X20927-110218

Notes relevant to the figure:

1. CH[0/1]_RXPROGDIVCLK is used as the source of the interconnect logic clock via BUFG_GT.

2. There is only one LCPLL in the GTM_DUAL primitive which is shared between the TX/RX.

3. RXRECCLK[0/1] is the same as CH[0/1]_RXPROGDIVCLK. It can be routed to the

MGTREFCLK output pad to be used elsewhere.

RX Programmable Divider

The RX programmable divider shown in

Figure 41

uses the LCPLL output clock to generate a

parallel output clock. By using the transceiver LCPLL, RX programmable divider, and BUFG_GT,
CH[0/1]_RXPROGDIVCLK should be used as a clock source for the interconnect logic.

The following tables show the programmable divider ports and attributes, respectively.

Chapter 4: Receiver

UG581 (v1.0) January 4, 2019

www.xilinx.com

Virtex Ult GTM Transceivers

Send Feedback

Содержание Virtex UltraScale+ FPGAs


















































































































































Результаты поиска

Содержание Virtex UltraScale+ FPGAs

Отзывы:

Xilinx Virtex UltraScale+ FPGAs, Руководство пользователя, Страница: 95 / 145

Результаты поиска

Содержание Virtex UltraScale+ FPGAs

Отзывы: