Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 145

background image

TX PRBS pattern generator is disabled and the TX is driven based on the CH[0/1]_TXDATA
input.

TX Polarity Control

If TXP and TXN differential traces are accidentally swapped on the PCB, the differential data
transmitted by the GTM transceiver TX is reversed. One solution is to invert the parallel data
before serialization and transmission to offset the reversed polarity on the differential pair. The
TX polarity control can be accessed through the CH0_TXPOLARITY and CH1_TXPOLARITY
input from the interconnect logic interface. The TX polarity control is driven High to invert the
polarity of outgoing data.

Ports and Attributes

The following table defines the ports required for TX polarity control.

Table 40: TX Polarity Control Ports

Port

Dir

Clock Domain

Description

CH0_TXPOLARITY

In

CH0_TXUSRCLK2

The CH0_TXPOLARITY port is used to invert the

polarity of the outgoing data for channel 0:

0: Not inverted. TXP is positive, and TXN is

negative.
1: Inverted. TXP is negative, and TXN is

positive.

CH1_TXPOLARITY

In

CH1_TXUSRCLK2

The CH1_TXPOLARITY port is used to invert the

polarity of the outgoing data for channel 1:

0: Not inverted. TXP is positive, and TXN is

negative.
1: Inverted. TXP is negative, and TXN is

positive.

Notes:
1.

CH[0/1]_TXPOLARITY can be tied High if the polarity of TXP and TXN needs to be reversed.

TX Gray Encoder

GTM transmitters in Ult devices support two types of binary encoding options: linear
coding and Gray coding. By using Gray coding, only one bit error per symbol is made for incorrect
decisions, thus reducing the bit-error rate by more than 33%. The following figure illustrates the
differences between linear coding and Gray coding.

Chapter 3: Transmitter

UG581 (v1.0) January 4, 2019

Virtex Ult GTM Transceivers

71

«
...
69
70
71
72
73
...
»

Содержание Virtex UltraScale+ FPGAs


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex UltraScale+ FPGAs

Бренд: Baofeng Страницы: 4

Бренд: Baofeng Страницы: 22

Бренд: E+E Elektronik Страницы: 2

Бренд: Icom Страницы: 36

Бренд: DMP Electronics Страницы: 4

Бренд: Zenith Страницы: 32

ATS-909X - WORLD BAND RADIOS

Бренд: Sangean Страницы: 11

Бренд: Net Safety Страницы: 50

Бренд: Sennheiser Страницы: 6

Бренд: Teleco Страницы: 2

Бренд: BD Sensors Страницы: 2

Бренд: ClearSounds Страницы: 30

Бренд: Xoro Страницы: 48

Бренд: AirTest Страницы: 2

Бренд: PCB Piezotronics Страницы: 17

Бренд: Seli Страницы: 69

Бренд: Triax Страницы: 8

Бренд: Yaesu Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды