Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 145

Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 19

Figure 9:

Internal Dual Clocking Architecture

LCPLL

GTM_DUAL

REFCLK

Distribution

GTM Channel 0 (CH0)

TX PMA

TX PCS

RX PMA

RX PCS

GTM Channel 1 (CH1)

TX PMA

TX PCS

RX PMA

RX PCS

X20900-061418

The LCPLL input clock selection is described in

Reference Clock Selection and Distribution

LCPLL outputs feed the TX and RX clock divider blocks, which control the generation of serial
and parallel clocks used by the PMA and PCS blocks. The LCPLL is shared between the TX and
RX datapaths.

The figure below illustrates a conceptual view of the LCPLL architecture. The input clock can be
divided by a factor of M before it is fed into the phase frequency detector. The feedback divider
N determines the voltage-controlled oscillator (VCO) multiplication ratio. For line rates below
28.1 Gb/s (NRZ) and 56.2 Gb/s (PAM4), a fractional-N divider is supported where the effective
ratio is a combination of the N factor plus a fractional part. The LCPLL output frequency depends
on the settings of LCPLLCLKOUT_RATE. When LCPLLCLKOUT_RATE is set to HALF, the output
frequency is half of the VCO frequency. When it is set to FULL, the output frequency is the same
as the VCO frequency. A lock indicator block compares the frequencies of the reference clock
and VCO feedback clock to determine if a frequency lock has been achieved.

Chapter 2: Shared Features

UG581 (v1.0) January 4, 2019

Virtex Ult GTM Transceivers

19

«
...
17
18
19
20
21
...
»

Содержание Virtex UltraScale+ FPGAs


















































































































































Отзывы:

Нет отзывов