Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 91

Страница: 91 / 145

Table 51: RX Equalizer Attributes (cont'd)

Attribute

Type

Description

CH[0/1]_RX_APT_CFG28A[15:0]

16-bit

Adaptation loop override controls. Use the recommended

value from the Wizard.

Bit

Description

[15:13]

Reserved.

[12]

Enable to override automatic gain control

(AGC) value according to attribute

CH[0/1]_RX_APT_CFG18A[11:6].

[11]

Enable to override CTLE High frequency

loop (KH) value according to attribute

CH[0/1]_RX_APT_CFG18A[5:0].

[10]

Enable to override CTLE Low frequency loop

(KL) value according to attribute

CH[0/1]_RX_APT_CFG17B[12:7].

[9]

Enable to override Offset Cancelation (OS)

value according to attribute

CH[0/1]_RX_APT_CFG17B[6:0].

[8:5]

Reserved.

[4]

Enable to override FFE Tap HM4 value

according to attribute

CH[0/1]_RX_APT_CFG14B[5:0].

[3]

Enable to override FFE Tap HM3 value

according to attribute

CH[0/1]_RX_APT_CFG14B[11:6].

[2]

Enable to override FFE Tap HM2 value

according to attribute

CH[0/1]_RX_APT_CFG14A[7:0].

[1]

Enable to override FFE Tap HM1 value

according to attribute

CH[0/1]_RX_APT_CFG14A[15:8].

[0]

Adaptation override control. This bit must

be enabled to override the loops selected in

CH[0/1]_RX_APT_CFG28A, and

CH[0/1]_RX_APT_CFG28B. If this this bit is

set to low, all loops will be auto-adapting.

Chapter 4: Receiver

UG581 (v1.0) January 4, 2019

www.xilinx.com

Virtex Ult GTM Transceivers

Send Feedback

Содержание Virtex UltraScale+ FPGAs


















































































































































Результаты поиска

Содержание Virtex UltraScale+ FPGAs

Отзывы:

Похожие инструкции для Virtex UltraScale+ FPGAs

Бренды по названию

Популярные бренды

Xilinx Virtex UltraScale+ FPGAs, Руководство пользователя

Результаты поиска

Содержание Virtex UltraScale+ FPGAs

Отзывы:

Похожие инструкции для Virtex UltraScale+ FPGAs

Бренды по названию

Популярные бренды