Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 145

background image

Printed Circuit Board

Because the impedance between the power planes and GND has been kept low on the die and in
the package, the board design has a much more relaxed requirement for decoupling on the
printed circuit board. The primary purpose of the PCB decoupling capacitors is to provide noise
isolation between the transceiver power supply pins and the external noise sources. Some
examples of external noise sources are:

• Power supply regulator circuits

• On-board digital switching circuits

• SelectIO signals from the Ult device

Decoupling capacitors should be provided on the PCB near the GTM transceiver power pins.
These capacitors reduce the impedance of the PCB power distribution network. The reduced
impedance of the PDN provides a means to attenuate noise from external sources before it can
get into the device package power planes. The noise at the power pins should be less than
10 mVpp over the band from 10 kHz to 200 MHz.

PCB Design Checklist

The following table is a checklist of items that can be used to design and review any GTM
transceiver PCB schematic and layout.

Table 74: GTM Transceiver PCB Design Checklist

Pins

Recommendations

MGTREFCLKP
MGTREFCLKN

When configured as an input:

•

Use AC coupling capacitors for connection to oscillator.

•

For AC coupling capacitors, see

Reference Clock Interface

•

Reference clock oscillator output must comply with the minimum and maximum input

amplitude requirements for these input pins. See the Ult device data sheets (see

http://www.xilinx.com/documentation

).

When configured as an output:

•

Use AC coupling capacitors for connection to receiving device.

•

For AC coupling capacitors use 0.01 μF.

•

For output signal characteristics, see the Virtex UltraScale device data sheet (see

www.xilinx.com/documentation

•

If reference pins are not used, leave the associated pin pair unconnected. However, if the

IBUFDS_GTME3/4 is instantiated in the design but not used, the associated pin pair should be

connected to GND.

Chapter 5: Board Design Guidelines

UG581 (v1.0) January 4, 2019

Virtex Ult GTM Transceivers

129

«
...
127
128
129
130
131
...
»

Содержание Virtex UltraScale+ FPGAs


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex UltraScale+ FPGAs

Бренд: Dakota Alert Страницы: 2

Бренд: Pansat Страницы: 32

Centronic VarioControl VC420

Бренд: Becker Страницы: 52

Бренд: M-system Страницы: 3

EchoStream EN1215EOL

Бренд: Inovonics Страницы: 2

Бренд: Marantz Страницы: 2

Бренд: ASCOM Страницы: 22

Бренд: adstec Страницы: 21

Бренд: M-system Страницы: 2

Бренд: COBHAM Страницы: 36

Бренд: dB Страницы: 101

Бренд: Pro2 Страницы: 4

Бренд: GTX Страницы: 7

Бренд: ITALCOPPIE SENSORI Страницы: 2

Бренд: COBHAM Страницы: 95

Бренд: Onkyo Страницы: 42

Бренд: National Страницы: 15

Бренд: Automatic Technology Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды