Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 145

Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 54

Chapter 3

Transmitter

This chapter shows how to configure and use each of the functional blocks inside the transmitter
(TX). Each transceiver includes an independent transmitter, which consist of a PCS and a PMA.
The following figure shows the functional blocks of the transmitter. Parallel data flows from the
device logic into the TX interface through the PCS and PMA, and then out the TX driver as high-
speed serial data.

Figure 24:

GTM Transceiver TX Block Diagram

Pattern

Generator

Polarity

FIFO

To RX Parallel

Data (Near-End

PCS Loopback)

From RX Parallel

Data (Far-End

PCS Loopback)

TX

Interface

FEC

Gray

Encoder

Pre-

Coder

TX PCS

PIS

O

TX

Driver

TX

Pre/

Pre2/

Post
Emp

TX PMA

X20910-052818

The key elements within the GTM transceiver TX are:

1.

2.

3.

4.

TX Pattern Generator

5.

TX Polarity Control

6.

TX Gray Encoder

7.

8.

TX Fabric Clock Output Control

9.

TX Configurable Driver

Chapter 3: Transmitter

UG581 (v1.0) January 4, 2019

Virtex Ult GTM Transceivers

54

«
...
52
53
54
55
56
...
»

Содержание Virtex UltraScale+ FPGAs


















































































































































Отзывы:

Нет отзывов