Xilinx Virtex UltraScale+ FPGAs Скачать руководство пользователя страница 75

Страница: 75 / 145

Table 43: TX Programmable Divider Ports

Port

Dir

Clock Domain

Description

CH[0/1]_TXPROGDIVRESET

Async

This active-High port resets the dividers as well

as the TXPRGDIVRESETDONE indicator. A reset

must be performed whenever the input clock

source is interrupted.

CH[0/1]_TXPRGDIVRESETDONE

Out

Async

When the input clock is stable and reset is

performed, this active-High signal indicates the

reset is completed and the output clock is

stable.

CH[0/1]_TXPROGDIVCLK

Out

Clock

TXPROGDIVCLK is the parallel clock output from

the TX programmable divider. This clock is the

recommended output to the interconnect logic

through BUFG_GT.

Table 44: TX Programmable Divider Attribute

Attribute

Type

Description

CH[0/1]_TX_DRV_CFG4

16-bit

Reserved.

Bit Name

Address

Description

TX_PROGDIV_SEL_FULLRATE

[15]

This attribute is used during the TX programmable divider

ratio selection. Set to

1’b1

to obtain the full rate of the

divided clock. Set to

1’b0

to obtain the half rate of the

divided clock.

Chapter 3: Transmitter

UG581 (v1.0) January 4, 2019

www.xilinx.com

Virtex Ult GTM Transceivers

Send Feedback

Содержание Virtex UltraScale+ FPGAs


















































































































































Результаты поиска

Содержание Virtex UltraScale+ FPGAs

Отзывы:

Похожие инструкции для Virtex UltraScale+ FPGAs

Бренды по названию

Популярные бренды

Xilinx Virtex UltraScale+ FPGAs, Руководство пользователя

Результаты поиска

Содержание Virtex UltraScale+ FPGAs

Отзывы:

Похожие инструкции для Virtex UltraScale+ FPGAs

Бренды по названию

Популярные бренды