Xerox 4050 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 115

Xerox 4050 Скачать руководство пользователя страница 13

XEROX DOCUPRINT IPS MESSAGES GUIDE

2-1

2.

2

DocuPrint 96/4635/180 IPS

messages

This chapter contains a list, in numerical order by code, of the
messages that you may encounter while using your Xerox DocuPrint
96, 4635, or 180 IPS. It also discusses the different kinds of
messages and other information provided by the printer control
console.

Printer control console messages

The 96/4635/180 printer control console gives you status and error
information regarding the printer, in the form of messages and icons
you can open. The kinds of information the control console provides
include:

•

Local controls and displays for jam clearance, paper loading/
unloading, and diagnostics/service (used by the service
representative). Two types of messages are displayed on the
printer control console: fault messages, which relate to printer
malfunctions, and information messages, which relate to printer
conditions such as low dry ink.

•

Touch-sensitive areas that allow you to select options by
touching the printer control console screen. A tone sounds
when you touch one of these areas.

•

Printer alarm consisting of three beeps, repeated for ten
seconds. The alarm is generated by any event that stops the
printer.

The alarm stops after three cycles or as soon as you start to
clear the fault condition (for example, when you open doors or
covers specified in the clearance instructions). You can stop the
alarm by pressing one of the printer control console buttons or
by selecting a function through the touch screen.

«
...
11
12
13
14
15
...
»

Содержание 4050




















































































































Отзывы:

Нет отзывов