Wood master Flex Fuel Скачать руководство пользователя страница 7

Страница: 7 / 76

March 2011

Flex Fuel Owner’s Manual

3: Safety

• All installation and operations must follow STATE and LOCAL CODES for wiring, plumbing, and firing of this

unit. These CODES may differ from this manual. Installation must be performed by a qualified installer.

• All Flex fuel models operate at atmospheric pressure. DO NOT obstruct, block, or plug the overflow tank.

• Never open the ash door during operation!

• Anyone who is not familiar with and/or has not been trained to operate the Flex fuel may not

operate the system. Only responsible adults should operate your furnace. If the furnace is not fired

properly damage could result and the warranty may be voided.

• Never allow children to play near or tamper with the furnace, fuels, tanks or any other part of the system.

• Always keep the area around, and in front of fuel door clean and free from combustible materials.

• Keep animals away from the furnace.

• The operation may not be continued or restarted in the event of visible damages (for example, water leaks,

thermal distortion, traces of smoke or fire, mechanical damages, etc.). Any damages must be repaired. In

the event of any doubts, please contact your authorized WoodMaster Flex fuel Dealer.

• Freeze protection must be guaranteed in all water-bearing parts in the event of extensive idle

periods of the system.

Note

: Your Flex fuel is not intended to be your only heat source. In the event that

your existing heat source will not back up your Flex fuel antifreeze must be used.

• The Flex fuel system must not be exposed to external mechanical stress (for example, as storage, climbing

support, brace, or similar). This also applies for single parts (doors, covers, etc.).

• Only touch the handles during the operation. Temperatures at other points (for example, chimney, ash

door, buffer tank, lines…) can be very high.

• Remember to recycle the packaging your Flex fuel was shipped in. In the long term properly recycle the

furnace if you replace your Flex fuel.

• The Flex fuel must be operated exclusively according to the guidelines for planning, assembly,

regulations, statutes and product related instructions. The manufacturer is not liable for damages and

their results, if they occurred due to improper assembly, operation, application and also inadequate

maintenance and cleaning.

• Do not connect this unit to a chimney flue serving another appliance. Follow all state/local codes.

• Load wood carefully to avoid injury to hands and fingers that may come into contact with furnace

opening.

• Read and follow these directions carefully. Retain this manual for as long as you own your Flex fuel.

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды