Wood master Flex Fuel Скачать руководство пользователя страница 43

Страница: 43 / 76

March 2011

Flex Fuel Owner’s Manual

Smoldering gas extraction! Please add more!

Smoldering gas extraction is activated. You can now add more bulk material. Press the ESC button for

3 – 4 seconds to deactivate smoldering gas extraction. Smoldering gas extraction is automatically

deactivated after several minutes.

Fan lag! Please wait!

Fan lag is activated for approximately 20 minutes after a power outage or when the safety temperature

limiter (STL) has been reset. The status will immediately change to “Bulk materials!” if any active

combustion is detected in the firebox during this lag period. Detection is based on the flue gas

temperature or air factor.

You cannot abort Fan Lag.

11.7 Indications

Your WoodMaster dealer can undertake pre settings so that the system operator receives various

instructions at the display. These instructions are not to be understood as a furnace malfunction or fault.

The instructions are solely to alert the system operator of possible erratic behavior.

The following instructions are possible:

When firing is not necessary

This instruction is displayed if the system operator wants to ignite the furnace and the buffer tank(s) is

(are) already full. Before firing, it is recommended that the buffer temperatures are checked. If the

temperature is still sufficient, it is recommended you postpone firing until later.

When filling is not necessary

(smoldering gas extraction is activated by the system operator)

This instruction is displayed if the system operator wants to activate smoldering gas extraction and the

buffer tank(s) is (are) already full.

11: Bulk Materials Mode

NOTE!

The buffer tank is already

full! Only increase firing

when sufficent demand is

assured!

Do you still wish to increase

firing?

NOTE!

The buffer tank is already

full! A boiler filling is only

reccommended when sufficent

demand is assured!

Do you still wish to add more?

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды