Wood master Flex Fuel Скачать руководство пользователя страница 22

Страница: 22 / 76

Flex Fuel Owner’s Manual

March 2011

It is only possible to switch the furnace on and off from the start screen. The currently selected

operating mode is indicated on the line “Selected furnace mode” (in this example “Bulk materials”).

The status line “Boiler is switched off!“ indicates that the furnace is switched off. Automatic furnace

start-up is only possible when the furnace is switched on.

7.1 Switching the Furnace On

The following picture shows a furnace currently running in operating mode “Bulk materials“ with

current operating status “Boiler is switched off!”.

To switch on the furnace, press and hold the control knob for 3 – 4 seconds.

The following confirmation message appears on the display for several seconds:

7: Switching the Furnace On/Off

FLEX FUEL

V 10.060 Tu, 12.09.10

Bulk materials
Boiler temperature:

Flue gas temperature:

Air factor:

Boiler is switched off!

81ºF

13:44

117ºF

7.40

Software Version

Date & Clock

Current

Actual Values

Selected

Furnace Mode

Status Line(s)

FLEX FUEL

V 10.060 Tu, 12.09.10

Bulk materials
Boiler temperature:

Flue gas temperature:

Air factor:

Boiler is switched off!

81ºF

13:44

72ºF

7.40

Your boiler

is switched on!

Boiler operating mode:

Bulk materials

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды