Wood master Flex Fuel Скачать руководство пользователя страница 34

Страница: 34 / 76

Flex Fuel Owner’s Manual

March 2011

Depending on the installed options, up to three furnace operating modes are available:

• Bulk materials

The furnace is operated using bulk material fuel. This must be manually ignited.

• Bulk materials auto control

The furnace is operated using bulk material fuel. This is automatically ignited by the igniter.

• Pellets auto control

The furnace is operated using pellets for fuel. This is automatically ignited and automatically fed.

Note: Always ensure that the insert corresponding to the furnace operating mode is fitted

in the firebox.

10.3 Changing the Furnace Operating Mode

You have verified that the correct insert for the required furnace operating mode is fitted in the

firebox and want to switch to another furnace operating mode. First check the current operating status

of your furnace since it is not always possible to change the operating mode (bulk material

combustion is in progress and you want to change to operating mode “Pellets auto control”). In this case,

changeover is not possible and the following message is shown on the display for several seconds:

Changeover in status “bulk materials!” not possible!

The following table summarizes the operational states which permit a change of furnace operating

mode:

10: Operating Modes

Possible Operating Status

Change-over possible for any operational status!

“Heat exchanger cleaning waiting

to be released!“

“Availability!”

Change-over possible for any operational status!

Change-over

from

Pellets - auto

control to

Bulk materials

to Pellets - auto

control

“Furnace is

switched off!”

“Furnace is

switched off!”

“Furnace is

switched off!”

“Furnace is

switched off!”

“Stop system!”

“Heat exchanger cleaning is

active!”

“Heat exchanger cleaning waiting

to be released!“

“Heat exchanger cleaning is

active!”

Pellets - auto

control to

Bulk materials

auto control

Bulk materials

auto control

to Pellets - auto

control

“Heat exchanger cleaning is

active!”

“Heat exchanger cleaning waiting

to be released!“

“Heat exchanger cleaning is

active!”

“Heat exchanger cleaning waiting

to be released!“

Bulk materials to

Bulk materials

auto control

Bulk materials

auto control to

Bulk materials

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды