Wood master Flex Fuel Скачать руководство пользователя страница 10

Страница: 10 / 76

Flex Fuel Owner’s Manual

March 2011

5: Installation

Your Flex fuel must be installed by a professional and should follow all local, state and federal laws

and regulations. Any use of an unapproved installation may result in a voided warranty.

It is recommended to have your installation approved by WoodMaster.

5.1 Location

Your Flex fuel can only be installed indoors where the temperature will not fall below 50

F. The furnace

may be installed inside the building that it serves or in an out building. Your Flex fuel must not be

allowed to freeze. Your Flex fuel does not need to be installed in the same structure that it serves.

Ensure that the floor that the furnace is placed on is level and able to support the weight of the furnace

plus the additional weight of the water and fuel.

There should be ample room around your Flex fuel to make loading and cleaning your furnace easier.

This area should also be clear of any easily combustible materials. Minimum clearances requirements is

11 inches for the top, 14 inches for the sides, 19.5 inches for the back and open to the front.

The room where the furnace is placed should allow ample venting to ensure proper air flow to the

furnace. The vent size requirements are 31 square inches for the Flex fuel 30 kW and 62 square inches for

the Flex fuel 60 kW.

Ensure the feet are in the bottom of the furnace. adjust the feet so the furnace sits level and the feet are

loaded evenly.

Below are the dimensions for both the Flex fuel 30 kW and Flex fuel 60 kW including all optional

accessories and chimney.

Chimney Mount

Pellet Tank

Pellet A

uger

nit

15.00

17.00

R14.00

R4.00

57.00

40.00

38.00

28.25

11.25

4.25

24.00

58.25

6.25

Chimney Mount

Pellet Tank

Pellet A

uger

nit

15.50

19.00

R14.00

R5.00

53.00

51.00

30.00

72.00

13.00

4.25

32.50

71.00

66.75

6.25

62.50

30 kW

60 kW

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды