Wood master Flex Fuel Скачать руководство пользователя страница 40

Страница: 40 / 76

Flex Fuel Owner’s Manual

March 2011

Now close the firebox door and wait unit the

status line changes from “Please ignite” to “Bulk

materials”. This changeover indicates that the

kindling has ignited across its surface and there

is sufficient flame to add wood. The change from

“Please ignite” to “Bulk materials” occurs when the

flue gas temperature exceeds the flue gas start

temperature. The induced draft fan will now regu-

late according to the furnace temperature.

11: Bulk Materials Mode

Now wait 1 to 2 minutes until a clean, full-area fire

bed has formed.

Now you can begin to lay a layer of the medium sized

bulk material in the firebox. It is recommended to

activate smoldering gas extraction while filling the

furnace. (section11.4) Again, you must ensure that this

is parallel to the walls with no cavities and that the

wood will not bind on the walls of the chamber.

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды