Wood master Flex Fuel Скачать руководство пользователя страница 30

Страница: 30 / 76

Flex Fuel Owner’s Manual

March 2011

9.8 Output Test – Heating Cycle

Note: Output tests may be preformed by the owner, however, damage can occur if preformed

incorrectly. Please contact your WoodMaster Flex fuel dealer for assistance.

An output test of all connected pumps and mixers can be performed in this menu, in order to be able to

test the correct operating method.

Note: The heating cycle program is interrupted, as long as the output test is performed.

The heating cycle output test should only be controlled by a professional.

Move the curser by turning the control knob to the output test – heating cycle line and press the control

knob. Following figure will appear on the screen:

You can now press the control knob to scroll through the items to select one to change. If the control

knob is turned to the right while the cursor is in the heading, then the menu “Output Test 2-heat cycle”

appears for more options. You may turn the control knob again to bring up the “Output Test 3-heat cycle”

menu.

Switching on the Outputs

Press the control knob and the cursor moves from the header to the first menu item mixer 1. By turning

the control knob, select the output that you would like to activate and press the control knob. The cursor

changes to the entry field. You can switch the output on and/or off by turning the control knob. The

input options change from Off to Open to Close in the entry fields of mixer 1 and mixer 2.

Press the control knob in order to save the selection and/or to leave the input field. The cursor now

changes back to the respective menu item. You can now switch another output on and/or off or exit the

menu by pressing the ESC key.

9.9 Output Test – Boiler

Note: Damages may occur to the furnace, for which the manufacturer is not liable, in the event of

an incorrect use of “Output test – boiler”. The outputs should never be activated too long, since this

may result in blocking the screw and therefore in blocking the respective motor. Please contact your

WoodMaster Flex fuel dealer for assistance.

Note: This menu is only visible when the status line is “Boiler is switched off!”.

All functions of important components of the furnace can be tested in this menu.

Output test 1-heat cycle

Heat cycle pump 1:

Heat cycle pump 2:

Heat cycle pump 3:

Heat cycle pump 4:

Heat cycle pump 5:

Heat cycle pump 6:

Heat cycle pump 7:

Heat cycle pump 8:

DHWR pump 1:

DHWR pump 2:

DHWR pump 3:

DHWR pump 4:

Off

9: Basic Furnace Settings

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды