Wood master Flex Fuel Скачать руководство пользователя страница 36

Страница: 36 / 76

Flex Fuel Owner’s Manual

March 2011

Turn the control knob to move the cursor to the line of the desired

operating mode. For example, the following picture

illustrates the selection of operating mode “Pellets auto control” .

BOILER OPERATING MODE

Bulk materials

Bulk materials auto control

Pellets auto control

selected boiler mode:

Bulk materials

10: Operating Modes

BOILER OPERATING MODE

Bulk materials

Bulk materials auto control

Pellets auto control

selected boiler mode:

Bulk materials

To change the furnace setting from “Bulk materials” to “Pellets

auto control” follow these directions:

Press the control knob and the line of the current furnace operating

mode will be highlighted (in this case “Bulk materials“).

boiler operating mode:

Pellets auto control

Confirm the operation by pressing the control knob. If you do not

want to make any changes, press the ESC button to exit the sub-menu.

A confirmation message is displayed once the control knob is pressed

to confirm the change. The following picture illustrates the confirma-

tion of a successful change to operating mode “Pellets auto control” .

BOILER OPERATING MODE

Bulk materials

Bulk materials auto control

Pellets auto control

selected boiler mode:

Pellets auto control

You will then be returned to the menu “BOILER OPERATING MODE“.

The line “selected furnace operating mode” also indicates that the

change-over has been successful.

FLEX FUEL

V 10.060 Tu, 12.09.10

Pellets
Boiler temperature:

Flue gas temperature:

Air factor:

Boiler is switched off!

XXXºF

13:44

XXXºF

X.XX

Press the ESC button to navigate backwards until you are returned to

the start screen.

The line displaying the current furnace operating mode will also indicate the successful change to operating

mode “Pellets” . If the furnace indicates the status “Boiler switched off!” and you wish to start the furnace with

the selected furnace operating mode, switch on the furnace by pressing the control knob for three seconds,

as described in section 7.

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды