Wood master Flex Fuel Скачать руководство пользователя страница 33

Страница: 33 / 76

March 2011

Flex Fuel Owner’s Manual

10.1 View of the Selected Operating Mode

When booting up the display, the set operating mode is automatically displayed for approximately 3

seconds. All Flex fuel systems contain "Bulk materials" operating mode. The following modes are

possible:

Operating mode - “Bulk materials“

Your furnace has the operating mode "Bulk materials" selected. This mode is available on all units.

Operating mode - “Bulk material auto control“

If your furnace has the optional igniter connected, then the operating mode “Bulk materials-automatic” is

enabled during commissioning or upon installation of an igniter by your dealer.

Operating Mode -”Pellets – Manual Filling“

Your Furnace can be loaded with wood pellets. Next to the furnace is a hopper that the furnace auto

feeds from. The hopper is manually refilled by the operator of the unit. The pellets are automatically

ignited by the igniter.

Note: Your Flex fuel furnace may not have the igniter or pellet option installed. If this is the

case the system will not let you select “ Bulk materials - auto control” or “Pellets - Manual Filling”.

10.2: Setting the Furnace Operating Mode

The currently selected furnace operating mode is shown on the line

“selected boiler operating mode” on the start screen.

10: Operating Modes

FLEX FUEL

V 10.060 Tu, 12.09.10

Bulk materials
Boiler temperature:

Flue gas temperature:

Air factor:

Boiler is switched off!

81ºF

13:44

117ºF

7.40

Software Version

Date & Clock

Current

Actual Values

Selected

Furnace Mode

Status Line(s)

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды