Wood master Flex Fuel Скачать руководство пользователя страница 24

Страница: 24 / 76

Flex Fuel Owner’s Manual

March 2011

8: Display

Overview:

All settings are changed using the Control Knob in the center of the operating unit. Turn the wheel to

scroll through the various menus, move the cursor to the settings or increase/decrease the values. Press

the control knob to access the menus, select the settings, confirm a modified setting. The control knob is

also used to start up the furnace and activate the smoldering gas extraction.

The ESC button to the right of the rotary button may be used at any time to quit a particular sub-menu.

Pressing this button several times will return you to the start screen. Press and hold the ESC button for 3

seconds when the start screen is displayed to switch off the furnace. Smoldering gas extraction can also

be deactivated by pressing the ESC button for 3 seconds. When making changes in a screen, pressing the

ESC button will NOT save the changes.

Back lit

Display

ESC

Button

Control Knob and

Operating/Start Button

Содержание Flex Fuel













































































Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды

Wood master Flex Fuel, Руководство пользователя

Результаты поиска

Содержание Flex Fuel

Отзывы:

Похожие инструкции для Flex Fuel

Бренды по названию

Популярные бренды